Abstract:The setting time of the paste and the rheological properties and microstructure of the mortar after replacing OPC cement with silica fume (SF), fly ash cenosphere (FAC) and nano-silica are studied as a reference for shotcrete applications. The suggested contents of SF, FAC and nano-silica are around 5–7.5%, higher than 20% and 1–3%, respectively, to meet the initial setting time specification. Viscosity and yield stress of mortar are highly dependent on water/cement ratio and paste/sand ratio. At the higher water/cement ratio, viscosity is more based on the paste itself. For SF of 2.5–10%, viscosity and yield stress increase, and the flowability of the mixture decreases. For FAC of 5–25%, viscosity and yield stress increase with a lower rate than SF, and flowability increases at 5% and then decreases as FAC content increases, which, however, is at the same level as the control. When SF and FAC are both added, a tortuous behavior of viscosity is shown. As nano-silica is further added, significant increases in viscosity and yield stress are shown. The compressive strengths of mortar with different supplementary cementitious materials (SCMs) at early ages are close. The difference in compressive strength after 28 days of standard curing is significant. The SF5-FAC15 group exhibits the largest increase in strength for 32.82%. At the age of 2.5 h, the macropore areas distribution of SF5-FAC25-NS1.5 test groups were 31.96%, indicating the lowest macropore area distribution. The secondary hydration reaction of supplementary cementitious materials (SCMs) continuously generates products that fill the pores, and the ultrafine filling effect of nanomaterials improves the compactness of the mortar microstructure and reduces the macropore area distribution. The mercury intrusion test results of the SF5-FAC25-NS1.5 group show that the pores are concentrated within the range of 0.01 to 0.05 μm, and the most probable pore size is significantly smaller than that of the CTR group. As the overall replacement level of SCMs increases, the diffraction peak of calcium hydroxide gradually weakens.

Influence of carbon nanofibres/silica fume on mechanical performance of cement mortars

Influence of Carbon Nanofibers on the Mechanical Performance and Microstructure of Cement-Based Materials

THE INFLUENCE OF CARBON NANOTUBES/SILICA FUME ON THE MECHANICAL PROPERTIES OF CEMENT-BASED COMPOSITES

Properties of cement-based composites with nano-SiO2 and carbon fibers

Effect of nano-SiO 2 /CaSO 4 whisker–silica fume on the strength, drying shrinkage, and capillary water absorption of cement mortar

Effect of nano-SiO2/CaSO4 whisker–silica fume on the strength, drying shrinkage, and capillary water absorption of cement mortar

INFLUENŢA NANOTUBURILOR DE CARBON - SILICEI ULTRAFINE ASUPRA PROPRIETĂŢILOR MECANICE ALE COMPOZITELOR PE BAZĂ DE CIMENT THE INFLUENCE OF CARBON NANOTUBES/SILICA FUME ON THE MECHANICAL PROPERTIES OF CEMENT-BASED COMPOSITES

Microstructure of Cement Mortar with Nano-Particles

Investigations on the Preparation and Mechanical Properties of the Nano-Alumina Reinforced Cement Composite

Rheological behaviour, setting time, compressive strength and microstructure of mortar incorporating supplementary cementitious materials and nano-silica

Influence of silicon-dioxide nanoparticles in cementitious mortars: verification using X-ray diffraction, thermal analysis, physical, and mechanical tests

Performance enhancement of silica fume blended mortars using bio-functionalized nano-silica

Influence of Nanoparticles on Fluidity and Mechanical Properties of Cement Mortar

Effect of carbon nanofibers on rheological and mechanical properties of cement composites

Effects of Carbon Nanotubes on Mechanical and 2D-3D Microstructure Properties of Cement Mortar

Effect of pore structure properties on strength properties of hybrid silica fume mortars containing randomly distributed carbon fibers

Modification Effects of Carbon Nanotube Dispersion on the Mechanical Properties, Pore Structure, and Microstructure of Cement Mortar

Combined Effect of Nano Ferrite and Nano Silica onProperties of Cement Mortar

Effect of silica fume-enhanced carbon nanotube dispersion on the strength and damping properties of cement composites

Influence of SiO<sub>2</sub>, TiO<sub>2</sub> and Fe<sub>2</sub>O<sub>3</sub> nanoparticles on the properties of fly ash blended cement mortars

Study on the Influence of Nanosilica Sol on the Hydration Process of Different Kinds of Cement and Mortar Properties