High Yield Production of HMF from Carbohydrates over Silica–alumina Composite Catalysts

Xiangcheng Li,Qineng Xia,Van Chuc Nguyen,Kaihao Peng,Xiaohui Liu,Nadine Essayem,Yanqin Wang

DOI: https://doi.org/10.1039/c6cy01628f

IF: 6.177

2016-01-01

Catalysis Science & Technology

Abstract:Mesoporous AlSiO catalysts have been prepared by a facile sol–gel method with tunable acidity for highly efficient production of HMF.

What problem does this paper attempt to address?

Highly Efficient One-Pot Conversion of Glucose to 5-Hydroxymethylfurfural over Acid–Base Bifunctional MCM-41 Mesoporous Silica under Mild Aqueous Conditions

Mahsa Niakan,Chao Qian,Shaodong Zhou

DOI: https://doi.org/10.1021/acs.energyfuels.3c02878

IF: 4.6541

2023-01-01

Energy & Fuels

Abstract:The one-pot synthesis of 5-hydroxymethylfurfural (HMF) from glucose as a cheap feedstock under mild conditions continues to be challenging for the chemical industry. Herein, a solid acid-base bifunctional catalyst was prepared by the postsynthetic modification of MCM-41 mesoporous silica with 3-chloropropyltriethoxysilane and subsequent anchoring of sulfanilic acid to its surface. A combination of N-2 sorption, X-ray diffraction, and transmission electron microscopy studies proved that the ordered mesostructure of MCM-41 was preserved during the process of catalyst preparation. The as-synthesized catalyst was successful in the one-pot production of HMF from glucose in an aqueous medium. The influences of numerous reaction parameters on the HMF yield were examined in detail. In optimal circumstances, 89% HMF was obtained by glucose conversion at 100 degrees C and 120 min using 20 mg of catalyst. Remarkably, the catalyst was tested up to six recycles and demonstrated no observable drop in catalytic performance, indicating its potential for industry applications.
Efficient One-Pot Production of 5-Hydroxymethylfurfural from Glucose in an Acetone–Water Solvent

Haoxiang Zhu,Youdi Zhang,Xusheng Guo,Youwei Cheng,Lijun Wang,Xi Li

DOI: https://doi.org/10.1021/acs.iecr.2c00502

2022-01-01

Industrial & Engineering Chemistry Research

Abstract:5-Hydroxymethylfurfural (HMF) is a high-valuebiomass-derived platform chemical derived from renewablebiomass, which is a great alternative to petroleum-based chemicals;however, it cannot be produced on a large scale at present becauseof the limitation of a low HMF yield and costly production. In thiswork, an experimental study of one-pot production of HMF fromglucose in an acetone-water solvent was conducted. The effects ofinorganic salts (in specific, NaCl) on miscible solvents were studiedbecause inorganic salts could affect the phase structure of solvents.We also study the influence of the ratio between Lewis acid andBronsted acid (L/B) on the dehydration reaction. After parameteroptimization experiments, up to 64.5% HMF yield was obtained at the condition ofC0= 1.25 w/v %,CAlCl3= 1.25 w/v %,CHCl=10mmolmiddotL-1,T= 160 degrees C, ando/a= 80/20, and the optimized L/B was 1.25 kgmiddotmol-1. Finally, an economic and efficient HMFproduction process including HMF purification and catalyst recycling was proposed; the HMF product could be produced andseparated with high recovery (similar to 88%) and purity (similar to 85%) in the process. Ourfindings and analysis would provide support for thechoice of the reaction system and bifunctional catalyst synthesis in the subsequent industrial demonstration development
Conversion of glucose to 5-hydroxymethyl furfural in water-acetonitrile-dimethyl sulfoxide solvent with aluminum on activated carbon and maleic acid

Shen Zhang,Kuichuan Sheng,Xueli Chen,Ximing Zhang,Nathan S. Mosier

DOI: https://doi.org/10.1016/j.indcrop.2021.114220

IF: 6.449

2021-01-01

Industrial Crops and Products

Abstract:The development of sustainable, efficient routes for conversion of glucose in biomass to 5-hydroxymethylfurfural (HMF), an important green intermediate in the production of value-added chemicals and fuels, has emerged due to the need to replace depletion of non-renewable fossil sources and climate change caused by their use. In this study, we describe a highly efficient reaction system for the production of HMF with a combination of homogeneous catalyst and heterogeneous catalyst in a polar cosolvent. The catalyst system consists of activated carbon (AC) supported aluminum (AC-Al) and maleic acid (MA) dissolved in a mixture of water, acetonitrile (ACN) and dimethyl sulfoxide (DMSO). Kinetic analysis of HMF production from glucose shows that carbon supported aluminum catalyst in combination with homogeneous maleic acid favored fructose dehydration to HMF instead of the formation of insoluble humins when compared to dissolved aluminum chloride and maleic acid in the same solvent. In addition, the rate constant of HMF hydrolysis to levulinic and formic acid was lower for AC-Al compared to dissolved Al. Response surface methodology (RSM), with central composite rotatable design (CCRD), identified the optimum conditions for glucose conversion to HMF as 168 °C for 11 min with a predicted molar yield of 50.3 mol%, which compared well to the experimentally verified yield of 45.8 mol% for these reaction conditions. To test the influence of glucose concentration on HMF yield, a range of initial glucose concentrations were examined. Results showed that the HMF yield increased with the decrease of weight percentage of glucose, suggesting that second order reactions result in humins formation.
CuZnCoOx Multifunctional Catalyst for in Situ Hydrogenation of 5-Hydroxymethylfurfural with Ethanol As Hydrogen Carrier

Zihao Zhang,Siyu Yao,Changxue Wang,Miaomiao Liu,Feng Zhang,Xiaobing Hu,Hao Chen,Xin Gou,Kequan Chen,Yimei Zhu,Xiuyang Lu,Pingkai Ouyang,Jie Fu

DOI: https://doi.org/10.1016/j.jcat.2019.04.011

IF: 7.3

2019-01-01

Journal of Catalysis

Abstract:Catalytic in situ hydrogenation of 5-hydroxymethylfurfural (5-HMF) to 2,5-dimethylfuran (DMF) has received a great interest in recent years. However, the issue of the consumption of expensive hydrogen donors, such as secondary alcohols, limits its applications. In this work, a ternary CuZnCoOx catalyst, exhibiting a 99% yield of DMF from in situ hydrogenation of 5-HMF with ethanol as economical hydrogen donor, is developed. High resolution transmission electron microscopy (HRTEM), energy dispersive X-ray spectroscopy (EDS-mapping), X-ray diffraction (XRD) and temperature programmed reduction (TPR) reveal the synergy effect of each components. Reaction mechanism studies unravel the CoO x results in promoting in situ H-2 production from ethanol, the zinc oxide accelerates the aldehyde group (-CHO) hydrogenation to hydroxymethy] group (-CH2OH) and the formation of Cu-Co alloy significantly facilitate the hydrogenation of 5-HMF. Additionally, this ternary CuZnCoOx catalyst exhibits superior recyclability without losing any activity during 6 cycles experiment. (C) 2019 Elsevier Inc. All rights reserved.
Highly Efficient Production of 5-Methoxymethylfurfural from Fructose in Dimethyl Sulfoxide/Amberlyst-15 Catalytic System

Hui Yang,Feng Zhou,Hao Chen,Jing Li,Huixia Ma,Kequan Chen,Xiuyang Lu,Pingkai Ouyang,Jie Fu

DOI: https://doi.org/10.1021/acs.iecr.9b06392

2020-01-01

Industrial & Engineering Chemistry Research

Abstract:With the dwindling availability of fossil fuel resources and the dramatic increase in demand, 5-methoxymethylfurfural (MMF) obtained from renewable biomass resources has great potential as a fossil fuel alternative. In this work, a high yield (80.5%) of MMF was obtained from fructose catalyzed by Amberlyst-15 with the assistance of dimethyl sulfoxide (DMSO) in methanol at 100 degrees C for 10 h. Based on a detailed investigation of the reaction mechanism through the effects of DMSO, Amberlyst-15, reaction time, and reaction temperature on MMF yield and the existence of intermediates proved by FTIR, a two-step pathway was proposed: (1) DMSO and H ion on Amberlyst-15 act as a joint-catalyst [DMSOH](+), facilitating the dehydration of fructose into 5-hydroxymethylfurfural (HMF), and (2) [DMSOH](+) assists the etherification of HMF with methanol into MMF, which is the rate-determining step. This finding expands the concept of biomass conversion into biomass fuels and plays a vital role in catalyst screen and design, reaction medium selection, and industrial applications.
Selective 5-hydroxymethylfurfural production from cellulose formate in DMSO-H2O media

Caidi Jin,Ning Xiang,Xiao Zhu,E. Shuang,Kuichuan Sheng,Ximing Zhang

DOI: https://doi.org/10.1016/j.apcatb.2020.119799

2021-01-01

Abstract:5-hydroxymethylfurfural (HMF) can be widely converted into value-added chemicals and fuels production. Herein, we reported a sustainable and efficient approach for synthesizing HMF directly from cellulose. Facile formylation of cellulose with green and recyclable formic acid was developed for cellulose formate (CF) production. CF with special net-like structure and high degree of formyl substitution was prepared. The resultant CF exhibited excellent catalytic conversion and selectivity for HMF production comparable to monomeric glucose as reactant in dimethyl sulfoxide (DMSO)-H2O media. In our work, we presented molecular dynamics simulations to elaborate the preferential coordination of DMSO around formyl group, which promoted the solvation of formylated substrate in DMSO-H2O mixture, and the HMF yielded could be protected by DMSO without further degradation to levulinic acid or humins.
High Yield Production of 5-Hydroxymethylfurfural from Carbohydrates over Phosphated TiO2-SiO2 Heterogeneous Catalyst

Chao Wang,Qilin Zhang,Tingting You,Bo Wang,Hongqi Dai,Feng Xu

DOI: https://doi.org/10.15376/biores.13.4.7873-7885

2018-01-01

BioResources

Abstract:An efficient and selective process for the conversion of carbohydrates to 5-hydroxymethylfurfural (HMF) was applied over a novel phosphated TiO2-SiO2 (P-TiO2-SiO2) catalyst. The catalyst, synthesized by a facile sol-gel technique, was characterized by X-ray diffraction (XRD), N2 sorption, NH3 temperature-programmed-desorption, and Fourier transform infrared spectroscopy (FT-IR) study of the pyridine adsorbed. The highest HMF yield of 63.0 mol% was achieved at 170 °C for 90 min over P-TiO2-SiO2 catalyst in a tetrahydrofuran (THF)/H2O-NaCl system. The P-TiO2-SiO2 catalyst showed a predominant catalytic performance in the synthesis of HMF, a result of its moderate acid density and suitable Bronsted/Lewis (B/L) acid ratio. Additionally, the catalyst was shown to be efficient in the conversion of more complex cellulose with the high HMF yield of 56.0 mol%. More importantly, this mesoporous catalyst exhibited high stability and recyclability, making it a promising choice for the future production of HMF.
Highly selective production of renewable p-xylene from bio-based 2,5-dimethylfuran and ethylene over Al-modified H-Beta zeolites

Rongrong Zhao,Lulu Xu,Shengjun Huang,Weiping Zhang

DOI: https://doi.org/10.1039/c9cy01113g

IF: 6.177

2019-01-01

Catalysis Science & Technology

Abstract:Highly selective synthesis of renewable p-xylene (PX) from bio-based 2,5-dimethylfuran (DMF) and ethylene was successfully realized on H-Beta zeolite catalysts with further Al-modifications. The influences of different doping approaches on their reaction performances and coke deposition were systematically investigated. Solid-state NMR and SEM-EDS characterization indicates that the Al containing precursors have significant effects on the aluminum location and catalyst acidity. For H-Beta zeolite treated with aluminum nitrate, the contents of framework Al and Bronsted acid sites increase obviously, causing the formation of more hard coke on the used catalyst as shown in C-13 CP/MAS NMR and TPO profiles, while for H-Beta zeolite modified with aluminum isopropoxide, more non-framework Al are formed in the pores of H-Beta, leading to severer soft and hard coke deposition. However, H-Beta zeolite after further doping with alumina shows excellent and durable performances with a PX yield of 97% at a 2,5-DMF conversion of similar to 100%. It also has good stability and regeneration capability. Most importantly, the coke content decreases from 12 to 7 wt% on the spent H-Beta-alumina catalyst with mainly soft carbonaceous species due to its appropriate Bronsted/Lewis acid ratio. This work provides a deeper understanding of the role of B/L ratio in the sustainable conversion of 2,5-DMF and ethylene to p-xylene, paving the way for the synthesis of bulky chemicals from biomass feedstocks.
Synthesis and characterization of amorphous silica-alumina with enhanced acidity and its application in hydro-isomerization/cracking

Tao Li,Ling Zhang,Zhichao Tao,Caixia Hu,Chunli Zhao,Fengjiao Yi,Xiang Gao,Xiaodong Wen,Yong Yang,Yongwang Li

DOI: https://doi.org/10.1016/j.fuel.2020.118487

IF: 7.4

2020-11-01

Fuel

Abstract:Amorphous silica-aluminas with enhanced Brønsted acidity have been successfully synthesized via a novel acetic acid based sol-gel process. The resulting amorphous silica-aluminas possess an irregular spherical morphology, homogeneously element dispersion, and a high external surface area in the range of 374–594 m2/g with little contribution from micropores. By simply adjusting the molar Si/Al ratio in the synthesis precursor solution from 0.5 to 2.0, the total Brønsted acid site density firstly increases and then slightly decreases, consistent with the trend of summarized molar content of four and five-coordinated aluminum species. Among them, the amorphous silica-alumina with initial Si/Al ratio of 1.5 exhibits the highest Brønsted acid site density, and its supported Pt catalyst performs the highest activity resembling that of HBeta-based catalyst in the hydroisomerization of n-hexadecane. Meanwhile, a superior catalytic selectivity to multibranched isomers was received over the amorphous silica-alumina without strong Brønsted acid sites. Moreover, a remarkable stability (>2000 h) was also achieved in the hydrocracking of Fischer-Tropsch wax under industrially relevant reaction conditions. This sol-gel synthesis process provides a facile method to prepare amorphous silica-aluminas with outstanding texture and acid properties for catalytic refining in petrochemical fields.

energy & fuels,engineering, chemical
Synthesis of a Sulfated-Group-riched Carbonaceous Catalyst and Its Application in the Esterification of Succinic Acid and Fructose Dehydration to Form HMF

Liu Huihui,Peng Qian,Ren Jiawen,Shi Bianfang,Wang Yanqin

DOI: https://doi.org/10.1007/s13738-021-02220-0

2021-01-01

Journal of the Iranian Chemical Society

Abstract:A novel sulfated-group-riched sulfonated carbonaceous catalyst with high acidic strength and adjustable ratio of acidic groups was designed in the paper, where glucose and benzyl chloride were hydrothermally carbonized first followed by sulfonation treatment. Various physicochemical techniques were used to characterize the catalyst such as IR, 13C MAS NMR and XPS spectra, NH3-TPD, XRD patterns and TG curve. Then, it was applied in the esterification of succinic acid and fructose dehydration to form HMF. Compared to commercial Amberlyst-15 catalyst, such carbonaceous solid acid exhibited excellent catalytic activity and thermal stability, which was attributed to its higher amount of sulfonic acid group.
Efficient 5-hydroxymethylfurfural synthesis from carbohydrates and food wastes in aqueous-natural deep eutectic solvent (A-NADES) with robust Al2O3 or Al(OH)3

Miao Zuo,Xinyu Wang,Wenlong Jia,Yanzhong Zhu,Xianhai Zeng,Lu Lin

DOI: https://doi.org/10.1016/j.fuel.2022.125062

IF: 7.4

2022-10-15

Fuel

Abstract:As one of the essential building blocks for bio-chemicals and bio-fuels, the 5-Hydroxymethylfurfural (HMF) production is still challenging in a green and cheap way. This work developed a bio-derived aqueous-natural deep eutectic solvent (A-NADES) to synthesize HMF using α-Al2O3 or Al(OH)3 as robust catalysts, obtaining high yields of 67.1% and 63.6% HMF from glucose under mild reaction reactions, respectively. Different kinds of starches and starchy food waste also exhibited high conversion efficiency in the A-NADES system. The mechanistic study indicated that the in-situ formed Al (III) site of α-Al2O3 during the reaction was critical for converting glucose-based carbohydrates. A-NADES could be effectively reused six times with a more convenient direct reuse method without significant activity loss. This study suggested a novel A-NADES reaction media in the synergistic reaction with robust aluminum-based catalysts for HMF synthesis, and proposed a novel process of food waste utilization in green solvents.

energy & fuels,engineering, chemical
AlNb/SBA-15 Catalysts with Tunable Lewis and Bronsted Acidic Sites for Glucose Conversion to HMF

Yong Wang,Liwei Zhu,Yuan Zhang,Hongyou Cui,Weiming Yi,Feng Song,Pingping Zhao,Xiuyu Sun,Yujiao Xie,Lihong Wang,Zhihe Li

DOI: https://doi.org/10.1002/slct.201800081

2018-01-01

ChemistrySelect

Abstract:In this paper, a series of AlNb/SBA-15 catalysts with various Al/Nb atom ratios were prepared by impregnation method for efficient conversion of glucose to 5-hydroxymethylfurfural (HMF). Characterization by SEM, TEM, BET and XRD showed that the microstructure after impregnation of the active components was preserved, similar to that of SBA-15, although the pore size and specific surface area decreased to some extent with the increase of Al/Nb atom ratio due to the thickening of the pore wall, which was due to the deposition of the active component salts. Py-IR and NH3-TPD analysis indicated that AlNb/SBA-15 had both Bronsted acid sites and Lewis acid sites simultaneously after incorporation of the Al species and they were tunable by adjusting the Al/Nb atom ratio. The catalyst with Al/Nb atom ratio of 2:3 exhibited the suitable strength of Lewis and Bronsted acid and the highest total acid amount, as a result, showing the highest catalytic activity in glucose dehydration to HMF. As high as 55.7% of HMF yield with 93.4% glucose conversion was obtained when reacting at 170 degrees C for 6.0h using methyl iso-butyl ketone (MIBK)/water with a volume ratio of 2 as the reaction media.
Transformation of Carbohydrates to 5-Hydroxymethylfurfural with High Efficiency by Tandem Catalysis

Yifan Nie,Qidong Hou,Chunyunlong Bai,Hengli Qian,Xinyu Bai,Meiting Ju

DOI: https://doi.org/10.1016/j.jclepro.2020.123023

IF: 11.1

2020-01-01

Journal of Cleaner Production

Abstract:Production of 5-hydroxymethylfurfural (HMF) is a pivotal step in biorefinery. However, the intrinsic HMF production efficiency in traditional catalytic systems are low owing to the side-reactions. Here we report the highly efficient transformation of carbohydrates to HMF via tandem catalysis in heterogeneous catalytic system. The combination of Al and Sn co-modified hydroxyapatite catalyst (Al/Sn-HAP) with ionic liquid exhibit a low activation energy of 68.4 kJ mol(-1), affording HMF yields of 70.5 and 46.6% at glucose loading of 10 and 40 wt%, respectively. Compared with other catalysts, Al/Sn-HAP exhibits remarkably higher Lewis acid concentration, specific surface area and pore dimeter with slight BrOnsted acid, as are beneficial for glucose isomerization. The efficient conversion of maltose, cellobiose and starch to HMF are achieved via the triple tandem pathway consisted of hydrolysis, isomerization and dehy-dration with inhibited side-reaction. Besides, the Al/Sn-HAP catalyst after regeneration can be reused without decrease of catalytic performance. (C) 2020 Elsevier Ltd. All rights reserved.
Porous nitrogen-doped carbons supporting Fe-porphyrins for the highly efficient catalytic oxidation of HMF to HMFCA

De Gao,Feng Han,Geoffrey I. N. Waterhouse,Yan Li,Lili Zhang

DOI: https://doi.org/10.1007/s13399-022-03512-y

IF: 4.05

2022-11-16

Biomass Conversion and Biorefinery

Abstract:A series of FeTPP-N/C-X catalysts were successfully prepared by adsorption of Fe tetraphenylporphine (FeTPP) onto a porous nitrogen-doped carbon (N/C) support using an ultrasonication method. The FeTPP-N/C catalysts were then used for the preparation of 5-hydroxymethyl-2-furan acid (HMFCA) by catalytic oxidation of 5-hydroxymethylfurfural (HMF) at 80 °C. The effects of reaction temperature, NaOH dosage, reaction time, and oxygen pressure on HMF conversion and HMFCA yield were systematically investigated. Under optimized testing conditions, a FeTPP-N/C-1 catalyst prepared using equal masses of FeTPP and N/C delivered a HMF conversion in water of 92.4%, with a selectivity to HMFCA of 97.2% over 6 h at an oxygen pressure of 1.0 MPa. Further, the catalyst showed good stability in five consecutive HMF oxidation tests. Based on the catalytic tests, and detailed catalyst characterization studies before and after reaction, a probable reaction mechanism was proposed for the selective oxidation of HMF to HMFCA by the FeTPP-N/C catalysts.Graphical AbstractA series of FeTPP-N/Ccatalysts were successfully prepared by the adsorption of irontetraphenylporphine (FeTPP) onto a porous nitrogen-doped carbon (N/C) supportusing an ultrasonication method. The FeTPP-N/C catalysts were then used for thecatalytic aerobic oxidation of HMF to HMFCA. Under the optimized reaction conditions (temperature80 °C, reaction time 6 h, O2 pressure 1 MPa), a high HMF conversionof 92.4% and a remarkable HMFCA selectivity of 97.2% were obtained, suggestingthat the developed noble-metal free catalyst has excellent promise for thesynthesis of valuable HMFCA from HMF.

energy & fuels,engineering, chemical
Aluminum Fluoride Modified HZSM-5 Zeolite with Superior Performance in Synthesis of Dimethyl Ether from Methanol

Qi Yang,Meng Kong,Zheyong Fan,Xiangju Meng,Jinhua Fei,Feng-Shou Xiao

DOI: https://doi.org/10.1021/ef3006383

IF: 4.6541

2012-01-01

Energy & Fuels

Abstract:A series of HZSM-5 catalysts modified with various loadings of aluminum fluoride (AlF3) were prepared from a mechanical mixture route. Combined characterizations of X-ray diffraction, Fourier transform infrared (FT-IR), Al-27, Si-29, F-19 MAS NMR, N-2 sorption, and NH3-tempeature-programmed desorption (NH3-TPD) techniques show that the structure, texture, and acidity of HZSM-5 catalysts can be adjusted with the loading of AlF3. A suitable amount of AlF3 modification (2 wt %) could increase the framework aluminum content and the surface area of HZSM-5. However, when the loading of AlF3 came to 3 wt % or more, the contrary results were obtained, which could be ascribed to the dealumination of the zeolitic framework. The catalytic activities for dehydration of methanol to dimethyl ether(DME) show that suitable amount of AlF3-modified HZSM-5 exhibited much higher activity and better stability than parent HZSM-5. The combination of "tunable" synthesis and "superior" properties is very much valuable in the academic and industry.
Silicotungstic acid catalyst supported onto functionalized halloysite nanotubes (HNTs) utilized for the production of 5-hydroxymethylfurfural (5-HMF) from fructose

Zahra Hosseini,Mohammad Kazemeini,Samahe Sadjadi,Sina Pourebrahimi

DOI: https://doi.org/10.1016/j.mcat.2024.113992

IF: 4.6

2024-03-06

Molecular Catalysis

Abstract:5-Hydroxymethylfurfural (5-HMF) is a valuable organic compound commonly derived from sugars such as fructose and glucose. Silicotungstic acid (HSiW), a unique Keggin-type heteropolyacid, is a typical catalyst for organic compound production. To synthesize 5-HMF from fructose, we developed a novel catalyst, HSiW@F-HNTs, by combining HSiW and functionalized halloysite nanotubes (F-HNTs) modified with (3-amino-propyl) triethoxysilane (APTES), 2,4,6-trichloro-1,3,5-triazine (TCT), and l -arginine. We analyzed the physicochemical properties of HSiW@F-HNTs using the FT-IR, XRD, BET, FESEM, EDS, and XPS characterization techniques, confirming their suitability for fructose-to-5-HMF conversion. Through response surface methodology (RSM), we investigated and optimized the effects of reaction conditions on 5-HMF production yield. Optimal conditions were found to be a 102 °C reaction temperature, a 65 min reaction time, and an 8.5 wt.% catalyst loading, resulting in a 95 % yield of fructose-to-5-HMF conversion. We also conducted the kinetic and thermodynamic analyses to determine the reaction rate and activation energy (Ea) and estimate the changes in Gibbs free energy (Δ G ), enthalpy (Δ H ), and entropy (Δ S ) of the catalytic conversion reaction. Additionally, the prepared HSiW@F-HNTs catalyst could be recycled up to 9 times without a significant loss in activity, demonstrating its high stability for real-world applications.

chemistry, physical
Core–shell silica@Cu x ZnAl LDH catalysts for efficient CO 2 hydrogenation to methanol

Meng Lyu,Jianwei Zheng,Claire Coulthard,Jing Ren,Yufei Zhao,Shik Chi Edman Tsang,Chunping Chen,Dermot O'Hare

DOI: https://doi.org/10.1039/d3sc02205f

IF: 8.4

2023-09-02

Chemical Science

Abstract:The efficient production of methanol by reduction of CO 2 using green hydrogen is a promising strategy from both a green chemistry and a carbon net zero perspective. Herein, we report the synthesis of well-dispersed core–shell catalyst precursors using silica@Cu x ZnAl-LDHs that can convert CO 2 to methanol. The catalyst precursors can be formed using either a commercially available silica (ES757) or a mesoporous silica ( e.g. MCM-48). These hybrid materials show significantly enhanced catalytic performance compared to the equivalent unsupported Cu x ZnAl LDH precursor. Space-time yields of up to 0.7 g MeOH g cat −1 h −1 under mild operating conditions were observed.

chemistry, multidisciplinary
Synthesis of mesoporous molecular sieves and their application as supports for catalysts in F-T synthesis

Caili Su,Yunfan Zou,WeiXiong Pan,Dehua He,QiMing Zhu

1998-01-01

Journal of Fuel Chemistry and Technology

Abstract:Different mesoporous molecular sieves, MCM -41, Al - MCM - 41, HMS etc. are prepared under different conditions. The specific surface areas are measured by using BET method. The structures are characterized with XRD, SEM, etc.. The influences of synthesis conditions on the structures of mesoporous molecular sieves are described. The mesoporous molecular sieves are used as supports for catalysts in the hydrogenation of CO. The activity and selectivity to C 1∼C 4 hydrocarbons of these catalysts are studied and compared with that of ZrO 2/ZSM -5, ZrO 2/β and ZrO 2/HY. Because of the higher surface area and special pore structure of MCM -41, Zirconia supported on MCM -41 prepared under different conditions has higher selectivity to C 2 =∼C 4 = for CO hydrogenation than that of ZrO 2/ ZSM-5, ZrO 2/β and ZrO 2/HY.
Sulfonic acid functionalized β zeolite as efficient bifunctional solid acid catalysts for the synthesis of 5-hydroxymethylfurfural from cellulose

Xinyi Xing,Xian Shi,Mengya Ruan,Qichun Wei,Ying Guan,Hui Gao,Siquan Xu

DOI: https://doi.org/10.1016/j.ijbiomac.2023.125037

2023-07-01

Abstract:Introduction of the sulfonic acid group into H-β zeolite to prepare β-SO3H bifunctional catalysts for the efficient synthesis of 5-hydroxymethylfurfural (HMF) from cellulose. Catalysts characterization, such as XRD, ICP-OES, SEM (Mapping), FTIR, XPS, N2 adsorption-desorption isotherm, NH3-TPD, Py-FTIR demonstrate the sulfonic acid group was successfully grafted onto the β zeolite. A superior HMF yield (59.4 %) and cellulose conversion (89.4 %) was obtained in the H2O(NaCl)/THF biphasic system under 200 °C for 3 h with β-SO3H(3) zeolite as catalyst. More valuable, β-SO3H(3) zeolite converts other sugars and obtains ideal HMF yield, including fructose (95.5 %), glucose (86.5 %), sucrose (76.8 %), maltose (71.5 %), cellobiose (67.0 %), starch (68.1 %), glucan (64.4 %) and also converts plant material (25.1 % for moso bamboo and 18.7 % for wheat straw) with great HMF yield. β-SO3H(3) zeolite catalyst keeps an appreciable recyclability after 5 cycles. Moreover, in the presence of β-SO3H(3) zeolite catalyst, the by-products during the production of HMF from cellulose were detected, and the possible conversion pathway of cellulose to HMF was proposed. The β-SO3H bifunctional catalyst has excellent potential for the biorefinery of high value platform compound from carbohydrates.
Preparation of 5-Hydroxymethylfurfural Using Magnetic Fe3O4@SiO2@mSiO2-TaOPO4 Catalyst in 2-Pentanol.

Xinglong Li,Mingming Li,Yuxin Liu,Yisi Feng,Pan

DOI: https://doi.org/10.1039/d2ra02182j

IF: 4.036

2022-01-01

RSC Advances

Abstract:5-Hydroxymethylfurfural (HMF) is one of the most important platform molecules and could be transformed into a variety of fuel additives and high value-added chemicals. Multiple catalyst systems have been developed for the conversion of carbohydrates to HMF, but there are still unavoidable problems, including high temperature and pressure, difficult recovery of solvent, corrosion of equipment, poor catalyst circulation, etc. Herein, a new magnetic Fe3O4@SiO2@mSiO2-TaOPO4 catalyst for the preparation of HMF from fructose in 2-pentanol was developed. The structures of the catalysts were characterized by FT-IR, TSM, EDS, SEM, XRD and VSM. The 2-pentanol solvent is not only conducive to the production of HMF, but also enables the reaction to be carried out at a lower pressure. The highest yield of HMF (85.4%) was obtained using 20 wt% catalyst under 10% substrate concentration (0.5 g of fructose) at 120 °C for 3 h. The catalysts can be easily separated by magnetism. The slight decrease in catalyst activity after 7 cycles was mainly due to the loss of catalyst during the cycle operation. Simultaneously, the total yield of HMF was 51.3% after scale-up to 15 g of fructose, showing the possible industrial application potential of this catalyst system.

High Yield Production of HMF from Carbohydrates over Silica–alumina Composite Catalysts

Highly Efficient One-Pot Conversion of Glucose to 5-Hydroxymethylfurfural over Acid–Base Bifunctional MCM-41 Mesoporous Silica under Mild Aqueous Conditions

Efficient One-Pot Production of 5-Hydroxymethylfurfural from Glucose in an Acetone–Water Solvent

Conversion of glucose to 5-hydroxymethyl furfural in water-acetonitrile-dimethyl sulfoxide solvent with aluminum on activated carbon and maleic acid

CuZnCoOx Multifunctional Catalyst for in Situ Hydrogenation of 5-Hydroxymethylfurfural with Ethanol As Hydrogen Carrier

Highly Efficient Production of 5-Methoxymethylfurfural from Fructose in Dimethyl Sulfoxide/Amberlyst-15 Catalytic System

Selective 5-hydroxymethylfurfural production from cellulose formate in DMSO-H<sub>2</sub>O media

High Yield Production of 5-Hydroxymethylfurfural from Carbohydrates over Phosphated TiO2-SiO2 Heterogeneous Catalyst

Highly selective production of renewable p-xylene from bio-based 2,5-dimethylfuran and ethylene over Al-modified H-Beta zeolites

Synthesis and characterization of amorphous silica-alumina with enhanced acidity and its application in hydro-isomerization/cracking

Synthesis of a Sulfated-Group-riched Carbonaceous Catalyst and Its Application in the Esterification of Succinic Acid and Fructose Dehydration to Form HMF

Efficient 5-hydroxymethylfurfural synthesis from carbohydrates and food wastes in aqueous-natural deep eutectic solvent (A-NADES) with robust Al2O3 or Al(OH)3

AlNb/SBA-15 Catalysts with Tunable Lewis and Bronsted Acidic Sites for Glucose Conversion to HMF

Transformation of Carbohydrates to 5-Hydroxymethylfurfural with High Efficiency by Tandem Catalysis

Porous nitrogen-doped carbons supporting Fe-porphyrins for the highly efficient catalytic oxidation of HMF to HMFCA

Aluminum Fluoride Modified HZSM-5 Zeolite with Superior Performance in Synthesis of Dimethyl Ether from Methanol

Silicotungstic acid catalyst supported onto functionalized halloysite nanotubes (HNTs) utilized for the production of 5-hydroxymethylfurfural (5-HMF) from fructose

Core–shell silica@Cu x ZnAl LDH catalysts for efficient CO 2 hydrogenation to methanol

Synthesis of mesoporous molecular sieves and their application as supports for catalysts in F-T synthesis

Sulfonic acid functionalized β zeolite as efficient bifunctional solid acid catalysts for the synthesis of 5-hydroxymethylfurfural from cellulose

Preparation of 5-Hydroxymethylfurfural Using Magnetic Fe3O4@SiO2@mSiO2-TaOPO4 Catalyst in 2-Pentanol.