Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Effect of Cluster Deposition on the Eutectic Structure in Binary Systems: A Monte-Carlo Simulation

Monte Carlo Simulation of the Dynamic Evolution of Binary Lamellar Eutectic in Directional Solidification

Formation of dendritic lamella in eutectic alloys

Phase-field simulation of binary alloy during directional solidification

Dynamics of directional coarsening in binary alloys: Monte-Carlo simulation

Effect of Material Parameters on Dendritic Patterns of Ni-Cu Binary Alloy Using Phase-Field Simulation

Phase-Field Simulation of Lamellar Growth for A Binary Eutectic Alloy

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

Numerical Simulation of Solute Segregation Patterns for a Binary Alloy Using Phase-Field Approach

Clustering and phase separation in a binary alloy on the FCC lattice

Effect of Element Bonding Energy on the Microstructure in the Growth of Eutectic Alloys

A Monte-Carlo Approach to Cellular-Pattern Evolution for Binary-Alloys During Directional Solidification

Modeling of Regular Eutectic Growth of Binary Alloy Based on Cellular Automaton Method

Monte-Carlo Simulation of Directional Growth of Lamellar Eutectic

Phase-field simulation of isothermal solidification of binary alloy based on KKS model

The Solidification of Al–Cu Binary Eutectic Alloy with Electric Fields

The formation mechanism of eutectic microstructures in NiAl-Cr composites

Effect of External Field on Dynamics of Phase Separation in Binary Alloys with Mobile Vacancies: a Monte Carlo Simulation

Effects of Computational Parameters on Solidification Structures Simulated with Phase-Field Method for a Ni-Cu Binary Alloy

Dynamics of Phase Separation in Alloys with Internal Elastic Energy: A Monte Carlo Approach

Monte-Carlo simulation of regular lamellar eutectic growth in binary systems