Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Multifunctional Dopamine-Assisted Preparation of Efficient and Stable Perovskite Solar Cells

Improved Crystallinity and Self-Healing Effects in Perovskite Solar Cells Via Functional Incorporation of Polyvinylpyrrolidone

Multifunctional Dapsone Additives Prepare Efficient and Stable Perovskite Solar Cells

Multiple Passivation of Electronic Defects for Efficient and Stable Perovskite Solar Cells

Multifunctional Enhancement for Highly Stable and Efficient Perovskite Solar Cells

A Reaction-and-assembly Approach Using Monoamine Zinc Porphyrin for Highly Stable Large-Area Perovskite Solar Cells

Smoothed Grain Boundary Grooves, Passivated Defects and Released Compressive Stresses Via Bulk Molecule Doping for Efficient Perovskite Solar Cells

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

3D Polydentate Complexing Agents for Passivating Defects and Modulating Crystallinity for High‐Performance Perovskite Solar Cells

Simultaneously Mitigating Anion and Cation Defects Both in Bulk and Interface for High‐Effective Perovskite Solar Cells

Reinforcing Perovskite Framework Via Aminotrifluorotoluene for Achieving Efficient and Moisture-Resistance Solar Cells

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Two‐Pronged Maneuver of Inner Regulation and Surface Repair for Stable Inorganic Perovskite Solar Cells with Ultralow Open‐Circuit Voltage Deficit

Reduced defects and enhanced Vbi in perovskite absorbers through synergetic passivating effect using 4-methoxyphenylacetic acid

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Small‐Molecule Targeting of Defect Passivation in All‐Inorganic Carbon‐based Perovskite Solar Cells

Improving stability and efficiency of three-dimensional perovskite solar cells with organophosphorus ligands

Multifunctional Molecular Bridge Enabled Interface Passivation and Strain Release for Stable and Efficient All-Inorganic Perovskite Solar Cells

All-in-one Additive Enables Defect Passivated, Crystallization Modulated and Moisture Resisted Perovskite Films Toward Efficient Solar Cells

Toward efficient, moisture-resistant and lead-leakproofness perovskite solar cells: Coordination-driven reconstructing homogeneous amorphous perovskitoid/crystalline perovskite photoabsorber

Polymer-assisted Crystal Growth Regulation and Defect Passivation for Efficient Perovskite Solar Cells