Abstract:Abstract Microstructural evolution occurs in lead free Sn-Ag-Cu (SAC) solder joints exposed to isothermal aging. Such changes lead to degradations in the mechanical properties and creep behavior of the solder, and can result in dramatic reductions in the board level reliability of lead-free electronic assemblies subjected to aging. In our recent research, Scanning Electron Microscopy (SEM) has been used to: (1) monitor aging induced microstructural changes occurring within fixed regions in selected lead-free solder joints, (2) create time-lapse imagery of the microstructure evolution, and (3) analyze the microstructural changes quantitatively and correlate to the observed mechanical behavior evolution. This approach has removed the limitations of many prior studies where aged and non-aged microstructures were taken from two different samples and could only be qualitatively compared. In our current study, the microstructural evolutions were observed in SAC305 (96.5Sn-3.0Ag-0.5Cu) and SAC_Q (SAC+Bi) exposed to isothermal conditions at T = 100 °C and 125 °C for several different regions from several different joints. The microstructures in several fixed regions of interest were recorded after predetermined time intervals of aging, which were 1 hour (up to 270 hours) and 250 hours (up to 7000 hours) for the long-term aging samples. The aging induced changes in microstructure have been correlated with the changes in mechanical behavior measured using uniaxial tensile testing. The area and diameter of each IMC particle were tracked during the aging process using the recorded images and imaging processing software. As expected, the analysis of the evolving SAC305 and SAC+X microstructures showed a significant amount of diffusion of silver and bismuth in the beta-tin matrix during aging. In particular, Ag3Sn particles coalesced during aging leading to a decrease in the number of particles. Any bismuth in the SAC+X microstructure was observed to quickly go into solution, resulting in solid solution strengthening. This primary occurred within the beta-Sn dendrites, but also in the Ag3Sn intermetallic rich regions between dendrites. The presence of bismuth in was also found to slow the diffusion process that coarsens the Ag3Sn IMC particles. The combination solid solution strengthening and a lower diffusion rate for Ag lead to reduced aging effects in the SAC+Bi alloy relative to the SAC305 solder alloy. The SAC_Q alloy was found to have significantly better high temperature mechanical properties relative to SAC305 at all prior aging conditions. In particular, the initial modulus and ultimate tensile strength of SAC305 experienced large degradations during high temperature aging, whereas the same properties of SAC_Q changed only slightly. These changes in mechanical behavior correlated well with the observed increases in the average IMC particle diameter and decreases in the number of IMC particles. The microstructural and material property degradations were especially large for SAC305 during the initial 50 hours of aging.

Dynamic resistance monitoring of aging process of pressureless sintered nano-silver joints

Microstructure Evolution and Fracture Mechanism of Sintered Nano-Ag Joints on Bare Copper During High Temperature Aging

Effect of Thermal Aging on the Reliability of Interconnected Nano-Silver Solder Joints

Joint Analysis and Reliability Test of Epoxy-Based Nano Silver Paste Under Different Pressure-Less Sintering Processes

Mechanical and Microstructural Analysis of an Ultra-Flexible Nano-Silver Paste Sintered Joint

Analysis of high-temperature aging and microstructure of FC LED solder joints of a silver conductive layer bonded using SAC solder

Microstructural Evolution and Mechanical Reliability of Transient Liquid Phase Sintered Joint During Thermal Aging

Microstructural and mechanical evolution of sintered nano-silver joints on bare copper substrates during high-temperature storage

Sintering bonding process with Ag nanoparticle paste and joint properties in high temperature environment

Effect of heating rate on bonding strength of pressure-free sintered nanosilver joint

Residual Stress and Warping Analysis of the Nano-Silver Pressureless Sintering Process in SiC Power Device Packaging

Investigation and Comparison of Aging Effects in SAC305 and Doped SAC+X Solders Exposed to Isothermal Aging

Effect of oxygen on microstructural coarsening behaviors and mechanical properties of Ag sinter paste during high-temperature storage from macro to micro

Microstructure of Ag Nano Paste Joint and Its Influence on Reliability

Thermal Fatigue and Creep Fracture Behaviors of a Nanocomposite Solder in Microelectronic/Optoelectronic Packaging

Micromechanical and microstructure evolution of leaded (SnPb) and lead-free (SAC305 and SnCu) mixed solder joints during isothermal aging

Interface evolution and mechanical properties of Sn–36Pb–2Ag solder joints under different aging conditions

Microstructural Response of Highly Porous Sintered Nano-silver Particle Die Attachments to Thermomechanical Cycling

An insight into dynamic properties of SAC305 lead-free solder under high strain rates and high temperatures

Thermal fatigue life prediction of Ag-2.5Sn solder joint in flip chip

Microstructural Evolution and Degradation Mechanism of SiC–Cu Chip Attachment Using Sintered Nano-Ag Paste During High-Temperature Ageing