Abstract:Carbon nanotubes-polydimethylsiloxane (CNT-PDMS) is a new type of laser ultrasonic transducer (LIU-T)composite material with high frequency, wide width and high amplitude. The composite film can be used as an efficient and robust ultrasonic emitter for diagnosis and treatment. The intrinsic structure of nanocomposites provides unique thermal, optical and mechanical properties, which are not only conducive to energy conversion but also robust to pulsed laser ablation. PDMS polymers have high thermoelastic coefficients that allow materials to stretch and produce ultrasound. In this paper, the characteristics of photoacoustic signals produced by several kinds of composite films are studied, the photoacoustic signal characteristics under the different substrate and water boundary conditions were tested. Photoacoustic transducers made of carbon nanomaterials with high light absorption and PDMS polymers with high expansibility not only reduce the thickness of materials but also are expected to generate high frequency and high intensity ultrasonic signals. The thickness of the hard glass substrate realized in this paper is about 1mm, the thickness of the soft film substrate is at the micron level, and the thickness of water boundary conditions are 3 mm. Under pulsed laser excitation, the ultrasonic pressure at the end surfaces of water boundary conditions and hard glass substrates and soft film substrates was 2. 0, 3. 9 and 5. 2 MPa, respectively. Through a series of studies, it is concluded that ; (1) soft film substrate (3 X 3) has better negative pulse than hard glass substrate (3 x 3), which is more suitable for photoacoustic cavitation treatment; (2) water boundary conditions are not conducive to the generation of high-intensity photoacoustic signals. In a word, compared with piezoelectric transducers, laser-induced ultrasonic transducers have more potential to produce high- amplitude ultrasonic signals with a wide width and provide a new method of ultrasonic excitation without interference structures such as electronics, which is expected to be a new generation of laser ultrasonic transducers to replace piezoelectric transducers. The application of this new method in magneto-acoustic imaging can greatly reduce the interference of ultrasonic excitation sources. At the same time, compared with mixing CNT into PDMS, the method adopted in this experiment is more simple, convenient and material saving. For traditional hard glass substrate, the implementation of soft film substrate can produce high sound pressure 5. 2 MPa, and center frequency in 5 MHZ, and -6 dB ultrasound is relatively close to 5 MHz wide bandwidth, compared with the 4. 5 MPa pressure produced by the early implementation of CNT-PDMS Photoacoustic transducer in 2014, this paper implementation has more clinical application prospect, applied in Magneto-acoustic electric imaging etc. to avoid electromagnetic interference has the very good effect.

A novel CNTs array-PDMS composite with anisotropic thermal conductivity for optoacoustic transducer applications

Effects of carbon nanotube thermal conductivity on optoacoustic transducer performance

Acoustic And Optoelectronic Nature And Interfacial Durability Of Modified Cnt And Gnp-Pvdf Composites With Nano-Structural Control

Multilayered Carbon Nanotube Yarn Based Optoacoustic Transducer with High Energy Conversion Efficiency for Ultrasound Application

Carbon Nanotube Composite Optoacoustic Transmitters for Strong and High Frequency Ultrasound Generation

Investigation on Laser-Induced Damage of CNT-PDMS Optoacoustic Transducer

Photoacoustic Properties of Carbon Nanotubes-Polydimethylsiloxane

A Novel Laser Ultrasound Transducer Using Candle Soot Carbon Nanoparticles

Candle Soot Nanoparticles-Polydimethylsiloxane Composites for Laser Ultrasound Transducers

Design and Prediction of Laser-Induced Damage Threshold of CNT–PDMS Optoacoustic Transducer

Flexible and high-intensity photoacoustic transducer with PDMS/CSNPs nanocomposite for inspecting thick structure using laser ultrasonics

Transparent microfiber Fabry-Perot ultrasound sensor with needle-shaped focus for multiscale photoacoustic imaging

Transparent Ultrasonic Transducers Based on Relaxor Ferroelectric Crystals for Advanced Photoacoustic Imaging

Active acoustic field modulation of ultrasonic transducers with flexible composites

Electrically Tunable Surface Acoustic Wave Propagation at MHz Frequencies Based on Carbon Nanotube Thin‐Film Transistors

Polydimethylsiloxane/Multi-Walled Carbon Nanotube Nanocomposite Film Prepared By Ultrasonic-Assisted Forced Impregnation With A Superior Photoacoustic Conversion Efficiency Of 9.98 X 10(-4)

High-consistent optical fiber photoacoustic generator with carbon nanoparticles-PDMS composite

Lithium Niobate-Based Optically Transparent Transducer for Broadband Ultrasound Transceiving

Thermoacoustic chips with carbon nanotube thin yarn arrays.

Broadband transparent ultrasound transducer with polymethyl methacrylate as matching layer for in vivo photoacoustic microscopy

Multipoint Energy-Balanced Laser-Ultrasonic Transducer Based on a Thin-Cladding Fiber