Abstract:Improving the toughness of epoxy resins (EP) with diverse thermoplastic polymers through curing reaction induced phase separation (RIPS) has been widely studied, with the prerequisite of designing and tailoring the phase morphology evolution of the blend. Herein, two typical amine-type curing agents, 4,4′-diamino diphenylmethane (DDM) with precuring temperature at around 150 °C and diethylenetriamine (DETA) at 80 °C were utilized to regulate and control the phase structures of EP-poly(ε-caprolactone) (PCL) blends. The curing temperature above or below the melting temperature (Tm) of PCL resulted in different states of PCL. The effect of curing temperature on the miscibility between EP matrix and PCL phase, and the correlation between phase morphology evolution and thermomechanical behavior, mechanical properties were comprehensively investigated for the first time. Results revealed that when the curing temperature of EPDDM-PCL blends was higher than the Tm of PCL, curing took place without phase separation; while distinct phase separation took place when EPDETA-PCL was cured at a temperature below the Tm of PCL. When the curing temperature was high, the PCL was able to dissolve completely in the resin before crosslinking began, so that semi-interpenetrating networks were formed; and that when the curing temperature was low, the PCL was unable to dissolve, and therefore formed separate particles. Consequently, the EPDDM-PCL blends exhibited all-leading mechanical properties due to the entanglement and slippage between PCL chains and EP networks. The strength of EPDETA-PCL was reduced but the toughness was improved for island-shaped PCL particles bridging or pinning the cracks during failure. These results elucidated the effect of the phase morphologies formed at different curing temperature on mechanical properties, and provided significant insights regarding the toughening of thermosets.

Regulation of ester contents enabled tunable thermal and mechanical properties of poly(ester amide)

Structural tuning of polycaprolactone based thermadapt shape memory polymer

Synthesis of novel poly(aminophosphonate ester)s flame retardants and their applications in EVA copolymer

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

SYNTHESIS AND CHARACTERIZATION OF POLYESTERAMIDES DERIVED FROM Ε-Caprolactam AND AMINOETHANOL

A New Generation of Poly(lactide/ε-Caprolactone) Polymeric Biomaterials for Application in the Medical Field.

Synthesis and Characterization of Segmented Poly(ether Ester Amide)s from Diglycol, Adipic Acid, and a Nylon‐6 Oligomer

Enhanced Crystallization Rate and Mechanical Properties of Poly(l‐lactic Acid) by Stereocomplexation with Four‐armed Poly(ϵ‐caprolactone)‐block‐poly(d‐lactic Acid) Diblock Copolymer

Facile Synthesis of Functional Poly( Ε -Caprolactone) Via Janus Polymerization

Effect of Composition on the Crystallization, Water Absorption, and Biodegradation of Poly(ε-caprolactam -co-ε-caprolactone) Copolymers

Epoxy Functionalised Poly(Epsilon-Caprolactone): Synthesis and Application

Synthesis, Characterization, and Properties of Poly(ester‐phosphoester)s by Lanthanum Triphenolate‐catalyzed Ring‐opening Copolymerization

Effect of Poly(ε-Caprolactone) Glycol Soft Segment Relative Molecular Mass on Properties of Polyurethane Elastomer Based on Poly(ε-Caprolactone) Glycol

Synthesis and Characterization of Thermoplastic Polyether-imide Elastormer

Synthesis of Poly(l-lactide-co-ε-caprolactone) Copolymer: Structure, Toughness, and Elasticity

Effects of curing temperature on the structure and properties of epoxy resin-poly(ε-caprolactam) blends

Effects of Poly(ε-caprolactone) on the Properties of Poly (lactic acid)/Poly (butylene succinate) Blends

Ring‐opening Copolymerization of Ethylene Carbonate and Ε‐caprolactone Catalyzed by Neodymium Tris(2,6‐di‐tert‐butyl‐4‐methylphenolate): Synthesis, Characterization, and Dynamic Mechanic Analysis

Synthesis and Characterization of Crystalline Graft Polymer Poly(ethylene Oxide)-G-poly(ɛ-caprolactone)2with Modulated Grafting Sites

Study on the synthesis and thermal behavior of biomedical poly(ε-caprolactone)