Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Wire arc additive manufacturing (WAAM) as an emerging manufacturing technique for fabricating large size metallic components with a higher deposition rate and lower material wastage. In this research, a thin walled-part was fabricated from stainless steel 316L with various heat input (HI) (low heat deposited wall (LHDW) and high heat deposited wall (HHDW) using the cold metal transfer (CMT)-based WAAM process. The microstructure characteristics, metallurgical characterization, and mechanical properties of the WAAM manufactured thin-walled component were examined. The deposited wall measuring 120 mm in length and 50 mm in height was fabricated by WAAM using ER316L wire and CMT. Microstructure of the deposit parts consists of the equiaxed, coarse, and columnar grains with epitaxial growth of dendrites were formed. The decrease in HI leads to the improvement of material hardness, yield and ultimate tensile strength (UTS) as well as the percentage elongation after fracture of the material decreases. EBSD analysis demonstrates the average grain size of 0.98 μm in LHDW and 2.43 in HHDW respectively. XRD results shows that main crystal structure found in WAAM thin-walled sample was γ-austenite phases. The microhardness distribution of the fabricated component exhibited the stability characteristics with the average value ranging between 213–237 HV. The tensile studies demonstrate the UTS of the LHDW and HHDW along the horizontal direction are 477 MPa greater than the vertical direction of 468 MPa and observed the anisotropy properties. The fractured surface was characterized by the emergence of obvious dimples revealing the ductile fracture. The lower HI and finer solidification structure of component fabricated by LHDW has greater tensile and hardness properties than that of HHDW. This study presents the initial assessment results for repairing stainless steel components subjected to mechanical damage.

Influence of Layer Thickness of RPV Steel Samples Prepared by WEDM Technology

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Effects of triaxial rolling on the microstructure and installation characteristics of reactor pressure vessel studs

The resistivity calculation method of reactor pressure vessel steels after ion irradiation

Effect of Repeated Weld Repairs on Microstructure and Mechanical Properties of Heat-Affected Zone in CA6NM Stainless Steel

OBSERVATION OF THE TRANSFORMATION IN MICROSTRUCTURE AND VICKERS HARDNESS OF FERROUS MODEL ALLOY BY ELECTROMAGNETIC INDUCTION HEATING TO FORM A HIGH TEMPERATURE GRADIENT

Magnetic Indicator for Evaluating Cu Clustering and Hardening Effect in RPV Model Alloy

Effects of Neutron Irradiation on Magnetic Properties of Reactor Pressure Vessel Steel

Study on Heat Input Effect of 316L Stainless Steel Thin-Walled Parts Processed by Wire Arc Additive Manufacturing

Electron beam welding beam current on microstructure and mechanical properties of AISI 316 austenitic stainless steel

Effect of heat treatment on the microstructure and mechanical property of W/316L multi-material fabricated by selective laser melting

Evolution of surface morphology and microstructure in reactor pressure vessel studs during triaxial rolling

Microstructure Heterogeneity and Mechanical Properties of a High-Strength Ductile Laminated Steel by Electron Beam Welding

Microstructure-Informed Prediction of Hardening in Ion-Irradiated Reactor Pressure Vessel Steels

Effects of Neutron Irradiation on Resistivity of Reactor Pressure Vessel Steel

Microstructural and Mechanical Property Analysis of High-Strength Low-Alloy Steel Tubes Fabricated Using Wire Arc-Directed Energy Deposition Technique

Effects of Neutron, Ion and Proton Irradiation on Nano-Indentation Hardness of RPV Steels

Investigation of Single and Double Pulse Techniques on Microstructure and Mechanical Anisotropy of Inconel 686 Component Fabricated by Wire Arc Directed Energy Deposition

The Unified Model for Irradiation Embrittlement Prediction of Reactor Pressure Vessel

Experimental study on the heat input behavior of wire-arc additively manufactured 316L stainless steel parts for repairing applications

Understanding the effect of phosphorous on the ion-irradiation behaviour of RPV model steels using atom probe tomography and nanoindentation