Abstract:In order to increase entry gas temperature and improve the efficiency of gas turbine, steam is used as a coolant instead of air. Much research has been carried out on the closed circuit steam cooling of vanes substituted with film-cooling using compressor air in recent years. Furthermore, by studying the steam flow and heat transfer characteristics in rib ducts, this investigation focuses on establishing the basis of steam cooling technology application in complex flow field of internally-cooled turbine vane.In this paper, a report and assessment of RSM method based on SSG turbulence model is performed with commercial computational fluid dynamics software ANSYS CFX. The numerical results of heat transfer coefficient and friction factors in square channels with 90 degree rib turbulators for Reynolds numbers of 10 000, 30 000 and 60 000 are compared with the experimental data from Han's. It is found that the obtained heat transfer coefficient distributions and friction factors match well with SSG turbulence model. In addition, the heat transfer distribution and. pressure drop of steam-cooled ducts are predicted under the same work conditions by using dry real gas model. The Reynolds number could be correlated with the Nusselt number. The impact of steam physical properties on heat transfer performance are researched detailedly by respectively changing the steam superheat and entry pressure.The results indicate that the RSM method with a suitable turbulence model is valuable for the air-cooled and steam-cooled duct with the acceptable engineering accuracy (less than 20%). Comparing the cooling efficiency between steam and air under the same operation condition, the advantage of using cooling steam is evident than using cooling air. Furthermore, the efficiency of the whole gas turbine system will be greatly improved through using the closed loop steam cooling system. Changing the steam superheat and entry pressure, it has little effect on the steam flow and heat transfer characteristics. Increasing the steam overheat would raise the friction factor. Contrarily, enhancing the entry pressure would decrease the friction factor.

Effect of Duct Aspect Ratio on Heat Transfer and Friction in Steam-Cooled Ducts with 60° Angled Rib Turbulators

Experimental Study on Forced Convection Hydraulic and Thermal Characteristics in a Dimpled Flat Duct

Experimental Investigation on Heat Transfer and Friction Characteristics of Ribbed Rectangular Channels Using Steam As Coolant

Forced Convective Heat Transfer and Pressure Drop of Air Flowing in a Rectangle Duct with Cross-Ribs on the Opposite Walls

The Effect of Cooling Conditions on Convective Heat Transfer and Flow in a Steam-Cooled Ribbed Duct

Effect of Aspect Ratio on the Flow and Heat Transfer Characteristics of Mist/steam in Rectangular Ribbed Channels

Heat Transfer and Pressure Drop Correlations for Rectangular Channels with Ribs

Contrastive Experimental Study on Heat Transfer and Friction Characteristics in Steam Cooled and Air Cooled Rectangular Channels with Rib Turbulators

Numerical Investigation Of Heat Transfer And Flow Characteristics In A Steam-Cooled Square Ribbed Duct

Influence of rib angle on heat transfer and flow characteristics in a rectangular channel used steam as the coolant

Experimental Study of Developing Turbulent Flow and Heat Transfer in Ribbed Convergent/divergent Square Ducts

Experimental and Numerical Investigation of Heat Transfer Inside Two-Pass Rib Roughened Duct (AR = 1:2) under Rotating and Stationary Conditions

Experimental Research for Comparison of Heat Transfer Characteristic of Air and Steam in Rectangular Ribbed Channels

Comparative Study of Convective Heat Transfer Performance of Steam and Air Flow in Rib Roughened Channels

Investigation on the flow and heat transfer of mist/steam cooling in two-pass ribbed channels with various aspect ratios

Numerical Prediction of 45° Angled Ribs Effects on U-shaped Channels Heat Transfer and Flow under Multi Conditions

Experimental Study of Forced Convection in a Rectangle Duc twith Cross-Ribs on the Opposite Walls

Numerical Study of Conjugate Heat Transfer of Steam and Air in High Aspect Ratio Rectangular Ribbed Cooling Channel

Experimental Study on Developing and Fully Developed Fluid Flow and Heat Transfer in Annular-Sector Ducts

Heat transfer performance comparison of steam and air in gas turbine cooling channels with different rib angles

Heat Transfer and Friction Characteristics in Steam Cooled Rectangular Channels with Rib Turbulators