Abstract:It is feasible to control the phase morphology and phase inversion for immiscible polymer blends to manipulate their properties. In this work, the blend of high-density polyethylene (HDPE)/polyoxymethylene (POM) was used as an example, to demonstrate the effect of shear on the phase morphology and resultant mechanical properties in immiscible polymer blends. To do so, a well defined “in-process morphology control” process during injection molding was conducted. That was: after making the blends via melt mixing, the injection-molded bars were prepared via a so-called dynamic packing injection molding equipment to impose a prolonged shearing on the melts during the solidification stage. Phase morphologies and crystal structures of the blends were estimated mainly through scanning electron microscopy, differential scanning calorimetry and 2D wide-angle X-ray scattering, respectively. For in-process morphology controlled samples, co-continuous structures, especially subinclusions inside another continuous phase induced by shear, were observed when the HDPE content was between 30wt% and 50wt%, leading to much early occurrence of phase inversion and also the lowest degree of orientation for both HDPE and POM. However, for samples obtained via conventional injection molding, a droplet morphology was always observed with HDPE dispersed in POM as the content of HDPE was up to 30wt%, but with POM dispersed in HDPE as the content of HDPE was 50wt%. The performances of injection-molded bars were mainly respect to the phase morphologies for samples obtained via conventional injection molding in which tensile properties continuously decreased with increasing of HDPE content up to 30wt% and then increased with further increasing of HDPE content. For the in-process morphology controlled samples, the tensile properties depended not only on the phase morphology, but more importantly on the degree of orientation. One observed only a slight decrease of tensile property as the content of HDPE was less than 15wt%, while an abrupt decrease when the content of HDPE was between 30wt% and 50wt%, probably due to the lowest degree of orientation in this composition range.

SPATIAL HIERARCHY AND INTERFACIAL STRUCTURE IN INJECTION-MOLDED BARS OF POLYOLEFIN BLENDS

Spatial Hierarchy and Interfacial Structure in Injection-Molded Bars of Polypropylene-Based Blends and Composites

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Shear-Induced Fibrillation and Resultant Mechanical Properties of Injection-Molded Polyamide 1010/isotactic Polypropylene Blends

Injection Molding-Induced Morphology of Thermoplastic Polymer Blends

The Hierarchy Structure and Orientation of High Density Polyethylene Obtained Via Dynamic Packing Injection Molding

Hierarchical structure and unique impact behavior of polypropylene/ ethylene-octene copolymer blends as obtained via dynamic packing injection molding

Shear-induced change of phase morphology and tensile property in injection-molded bars of high-density polyethylene/polyoxymethylene blends

Hierarchical structure of injection-molded bars of HDPE/MWCNTs composites with novel nanohybrid shish–kebab

Interfacial Crystalline Structures in Injection Over-Molded Polypropylene and Bond Strength.

Hierarchical crystalline structures and dynamic mechanical properties of injection-molded bars of HDPE: Attributes of temperature field

The High Mechanical Properties and Micro-Phase Separation of High Density Polyethylene and Polypropylene Blends

A novel hierarchical crystalline structure of injection-molded bars of linear polymer: co-existence of bending and normal shish–kebab structure

Alternating Multilayer Structure of Polyethylene/polypropylene Blends Obtained Through Injection Molding

Development of Morphology and Properties of Injection‐molded Bars of HDPE/PA6 Blends along Flow Direction

Combined Effect of Shear and Nucleating Agent on the Multilayered Structure of Injection‐molded Bar of Isotactic Polypropylene

The effect of shear on mechanical properties and orientation of HDPE/mica composites obtained via dynamic packing injection molding (DPIM)

Hierarchy structure in injection molded polypropylene/ethylene–octane copolymer blends

Influence of Matrix Polymer on Deformation and Morphology of Injection Molded Immiscible Blends with High Interfacial Contact

Morphology-Tensile Behavior Relationship in Injection Molded Poly(Ethylene Terephthalate)/Polyethylene and Polycarbonate/Polyethylene Blends (I) - Part I - Skin-Core Structure

Micro and macro injection molded parts of isotactic polypropylene/ polyethylene blends: Shear-induced crystallization behaviors and morphological characteristics