Abstract:Polylactide (PLA) underwent molecular degradation when it was exposed to gamma ray radiation, the degradation was inhibited somehow in the presence of 1-ally1 3 -methylimidazolium chloride (AMIMC1). The grafting reaction of AMIMC1 on PLA chains occurred during the irradiation to obtain imidazolium cations grafted PLA (PLA-IM). The molecular masses and the contents of end groups of the resultant PLA samples were measured by gel permeation chromatography (GPC) and nuclear magnetic resonance (1H-NMR), respectively. Compared with the PLA sample irradiated without AMIMC1 (PLA-S), PLA-IM possessed less hydroxyl end groups and higher molecular mass (3 times as high as that of PLA-S). The nucleation and growth of crystalline during isothermal crystallization process were observed using polarized optical microscopy (POM). The results revealed that PLA-IM possessed spherulitic morphology which was same as other PLA samples, and the growth rate of the spherulites was mainly dependent on the molecular mass of PLA samples, demonstrating highest growth rate for PLA-S, followed by PLA-IM and lowest for PLA-L at the same crystallization temperature. However, different from PLA-L and PLA-S, PLA-IM showed increased nucleation density in the whole experimental temperature range due to the presence of grafted imidazolium cations on PLA chains. Isothermal crystallization kinetics for the PLA samples was then investigated by differential scanning calorimetry (DSC) and analyzed using Avrami equation. The results showed that the crystallization rate of PLA-IM had improved obviously because of its higher nucleation density. When the isothermal crystallization temperature was higher than 125 degrees C, the half crystallization time of PLA-IM was shorter than that of PLA-S with lower molecular mass. Different from the retardant effect of ionic liquids (ILs) on PLA nucleation in PLA/ILs blends, the ionic interaction between the imidazolium cations grafted on PLA chains facilitates the orderly arrangement of PLA chains and formation of nuclei in the crystallization process, which contributes to the acceleration of crystallization kinetics.

Effect of Grafted Imidazolium Cations on Crystallization Behavior of Polylactide

Blending Effects on Polymorphic Crystallization of Poly(l-lactide)

Manipulation of Non-Isothermal Crystallization Kinetics of Poly(lactic Acid) Composite Film by a Novel Nucleating Agent

Crystallization Behavior and Isothermal Crystallization Kinetics of PLLA Blended with Ionic Liquid, 1‐butyl‐3‐methylimidazolium Dibutylphosphate

Introduction of Stereocomplex Crystallites of PLA for the Solid and Microcellular Poly(lactide)/poly(butylene Adipate-Co-terephthalate) Blends

Significant Enhancement of Crystallization Kinetics of Polylactide in Its Immiscible Blends Through an Interfacial Effect from Comb-Like Grafted Side Chains

Effect of poly(lactic acid) crystallization on its mechanical and heat resistance performances

Effect of 1,2,3-triazolium-functionalized PEG-b-PCL block copolymer on crystallization behavior of poly(L‐lactic acid) as nucleation agent and mobility promoter

Significantly Enhanced Crystallization of Polylactide Ingeo 4032D by Polyethylene Ionomer

Effect of POSS-NH2-grafted different plasticizers on the crystallization properties of SC-Poly (l-lactic acid)

Enhancing Crystallization Rate And Melt Strength Of Plla With Four-Arm Plla Grafted Silica: The Effect Of Molecular Weight Of The Grafting Plla Chains

Synergistic Effects of Polyethylene Glycol and Cellulose Nanofibers on the Isothermal and Non-isothermal Crystallization Behaviors of Polylactide

Preparation and properties of the crosslinked poly( L -lactide) with high crystallinity and high gel content

Influence of Non-Isothermal Melt Crystallization on the Thermal Behavior and Morphology of Poly-L-Lactide

Conformation Directed Mpemba Effect on Polylactide Crystallization

Mechanical Properties and Non-Isothermal Crystallization Kinetics of Polylactic Acid Modified by Polyacrylic Elastomers and Cellulose Nanocrystals

Enhancing Crystallization Behavior for Optimized Performances of Poly(tmc‐b‐(lla‐ran‐ga)) by PDLA/PLLA Stereocomplex Crystallization

Synergistic Effect of Poly(ionic Liquid) and Phosphoramide on Flame Retardancy and Crystallization of Poly(lactic Acid).

Effect of Nucleation of Tricalcium Phosphate and Isothermal Annealing on the Crystallization of Poly( l -lactide- co -glycolide)

Enhanced Nucleation and Crystallization of Poly(l-lactic Acid) by Immiscible Blending with Poly(vinylidene Fluoride)

Effect of nucleating agent incorporation on the crystallization and mechanical properties of polylactide/polyamide elastomer blends