Abstract:Perovskite solar cells based on the inorganic/organic hybrid perovskite have attracted increasing attention over the past 3 years. Many studies have been done in this area. Controling the morphology of the perovskite film is an effective way to improve the photoelectric conversion efficiency of the devices. In our reserch, we studied the influence of structure and morphology of perovskite films on the performance of the organic-inorganic hybrid perovskite solar cells which prepared by a sequential deposition method. Mesoporous TiO2 scaffold were introduced as electron collecting layer. Lead iodide (PbI2) was then spin cast on the TiO2 scaffold. The PbI2 subsequently transformed into the perovskite (CH3NH3PbI3) by dipping the TiO2/PbI2 film into a solution of CH3NH3I. We studied the difference between the PbI2 film with or without drying under room temperature after spin-coating. Through drying under room temperature, larger pores formed in the PbI2 film. While without drying under room temperature, smaller and shallower pores formed in the PbI2 film. The results show that larger pores in PbI2 film leads to more complete transformation of PbI2 to CH3NH3PbI3 and larger CH3NH3PbI3 particles. CH3NH3PbI3 films were prepared with three different processes: (a) direct dipping the PbI2 film with smaller pores into the CH3NH3I solution; (b) direct dipping the PbI2 with larger pores into the CH3NH3I solution; (c) dipping the PbI2 with larger pores into the CH3NH3I solution after pre-wetting. The resulting CH3NH3PbI3 films were studied with SEM, UV-vis absorption spectrum and XRD. The particles size of the CH3NH3PbI3 are 150, 250 and 350 rim for process (a), (b) and (c) respectively. CH3NH3PbI3 films fabricated through process (a) show insufficient absorption due to the insufficient transformation of the PbI2. The pre-wetting procedure leads to slower reaction result in larger CH3NH3PbI3 particle size. Devices with proper size of CH3NH3PbI3 particles show the highest photoelectric conversion efficiency. An efficiency of 13.5% was achieved with a J(sc) of 17.8 mA/cm(2), a V-oc of 1.05 V and a FF of 72.5%.

Unraveling the Roles of Mesoporous TiO2 Framework in CH3NH3PbI3 Perovskite Solar Cells

CH3NH3PbI3 and CH3NH3PbI3–xClx in Planar or Mesoporous Perovskite Solar Cells: Comprehensive Insight into the Dependence of Performance on Architecture

Influence of Structure and Morphology of Perovskite Films on the Performance of Perovskite Solar Cells

Elucidating the Roles of TiCl4 and PCBM Fullerene Treatment on TiO2 Electron Transporting Layer for Highly Efficient Planar Perovskite Solar Cells

Effect of the Device Architecture on the Performance of FA(0.85)MA(0.15)PbBr(0.45)I(2.55) Planar Perovskite Solar Cells

CH 3 NH 3 PbI 3 grain growth and interfacial properties in meso-structured perovskite solar cells fabricated by two-step deposition.

High-Performance Simple-Structured Planar Heterojunction Perovskite Solar Cells Achieved by Precursor Optimization.

Tuning the A-site Cation and X-site Anion Composition of CH3NH3PbI3 Perovskite Material for Efficient Planar Perovskite Solar Cells

A facile spray-assisted fabrication of homogenous flat CH3NH3PbI3 films for high performance mesostructure perovskite solar cells

TiO2/SnO2 Nanocomposites As Electron Transporting Layer for Efficiency Enhancement in Planar CH3NH3PbI3-Based Perovskite Solar Cells

High Efficient Planar-Heterojunction Solar Cells Achieved by Using A Smooth Ch3nh3pbi3 Film Via A New Approach of Forming the Pbi2 Nanostructure Together with Strategically High Ch3nh3i Concentration

Effects of Cyclic Tetrapyrrole Rings of Aggregate-Forming Chlorophyll Derivatives As Hole-Transporting Materials on Performance of Perovskite Solar Cells

High-performance Planar Heterojunction Perovskite Solar Cells: Preserving Long Charge Carrier Diffusion Lengths and Interfacial Engineering

(Invited) Improvement of Perovskite Films and the Perovskite/TiO2Interface

Lead Methylammonium Triiodide Perovskite-Based Solar Cells: an Interfacial Charge-Transfer Investigation.

Influence of TiO2 Layer on Ultimate Efficiencies for Planar and Nano-Textured CH3NH3PbI3 Solar Cells

Unraveling Film Transformations and Device Performance of Planar Perovskite Solar Cells

Enhanced Photovoltaic Performance of CH3NH3PbI3 Perovskite Solar Cells Through Interfacial Engineering Using Self-Assembling Monolayer.

Effect Of Chloride Substitution On Interfacial Charge Transfer Processes In Mapbi(3) Perovskite Thin Film Solar Cells: Planar Versus Mesoporous

Structure-Performance Relationships of Hole-Transporting Materials in Perovskite Solar Cells: Minor Structural Discrepancy Effects on the Efficiency

Interface studies of the planar heterojunction perovskite solar cells