Abstract:Calcium looping cycle for post-combustion CO2 capture has gained increasing attention worldwide. However, CaO-based sorbents derived from natural sources for calcium looping cycle experience rapid loss of capacity during high-temperature cyclic carbonation/calcination reactions. Synthesizing sintering-resistant CaO-based sorbents by adding a support material has been extensively studied as an effective method of combating the problem. The support material in the synthetic sorbents plays an important role in retaining the capacity, and various support materials have been tested in the literature. In practical reactors, sulfur is present and it has been reported that sulfation of sorbents will also reduce the CO2 capture capacity. However, thus far, it is not clear whether/how support material would affect sulfation of sorbents and, thus, CO2 capture. In this paper, four different support materials, such as Ca2MnO4, La2O3, Ca12Al14O33, and MgO, were studied. The cyclic CO2 capture performance of the synthetic sorbents made from CaO and the support materials were investigated in detail, in the presence of SO2 and steam. The results showed that a mass ratio of 20-25% support material would be optimum for synthesizing sorbents with high cyclic CO2 capture capacity, and Ca12Al14O33 and MgO seem to be more effective than Ca2MnO4 and La2O3. The 80:20 wt % CaO/MgO synthetic sorbent achieved the highest CO2 capture capacity under ideal conditions over 100 cycles. However, the CaO/MgO sorbent had a strong affinity to SO2 capture during cyclic reactions, especially in the presence of steam. Under realistic conditions (i.e., both SO2 and steam are present during carbonation), the CaO/MgO sorbent showed the highest cumulative SO2 capture capacity, whereas the CaO/Ca12Al14O33 sorbent obtained the highest CO2 capture capacity after 10 cycles. The smaller average crystallite size of MgO in the sorbent was responsible for the strong SO2 affinity of the CaO/MgO sorbent as well as its stable cyclic CO2 capture abilities under ideal conditions.

Understanding the Morphology of Supported Na2CO3/γ-AlOOH Solid Sorbent and Its CO2 Sorption Performance

Properties of a Nano CaO/Al2O3 CO2 Sorbent

Properties of a Nano CaO/Al<sub>2</sub>O<sub>3</sub>CO<sub>2</sub>Sorbent

Preparation and Co2 Sorption/Desorption of N-(3-Aminopropyl) Aminoethyl Tributylphosphonium Amino Acid Salt Ionic Liquids Supported into Porous Silica Particles

Regenerable MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure: Experimental and DFT Study

Characteristics of MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure

Developing a Novel CaO-Based Sorbent for Promoted CO2 Capture and Tar Reduction

Synthesis of CaO-based Sorbents Through Incorporation of Alumina/aluminate and Their CO2 Capture Performance

Kilogram-scale production and pelletization of Al-promoted CaO-based sorbent for CO2 capture

Hydrophobic interface-assisted casting of Al-supported, CaO-based sorbent pellets for high-temperature CO 2 capture

CO2 Capture Performance of CaO-Based Sorbents Prepared by a Sol–Gel Method

Development of New Potassium Carbonate Sorbent for CO2 Capture under Real Flue Gas Conditions

Synthesis, characterization, and CO(2) adsorptive behavior of mesoporous AlOOH-supported layered hydroxides.

A biomass-supported Na2CO3 sorbent for flue gas desulfurization.

Investigation on a Novel CaO–Y2O3 Sorbent for Efficient CO2 Mitigation

Development of Highly Effective CaO@Al2O3 with Hierarchical Architecture CO2 Sorbents Via a Scalable Limited-Space Chemical Vapor Deposition Technique

A comparative study on energy efficient CO2 capture using amine grafted solid sorbent: Materials characterization, isotherms, kinetics and thermodynamics

Comparative investigation on CO2 uptake performance of limestone-derived sorbents with different supports synthesized by impregnated layer solution combustion method

Effect of Support Material on Carbonation and Sulfation of Synthetic Cao-Based Sorbents in Calcium Looping Cycle

New insights into stabilizing mechanism of Ca9Al6O18 stabilizing Ca-based sorbents for CO2 cyclic capture under mild conditions

Strengthening performance of Al-stabilized, CaO-based CO 2 sorbent pellets by the combination of impregnated layer solution combustion and graphite-moulding