Abstract:Electromagnetic incremental forming (EMIF) is a novel and flexible technology for forming large-size thin-walled components. However, the practical challenge is how to effectively control the forming defects, e.g., wrinkling, local humps and depressions that are caused by the multi-station discharge and the large-size thin-walled structure of sheet. To this end, the formation mechanism and rules of defects during the EMIF process of a large-size thin-walled ellipsoid surface part of aluminum alloy are studied through numerical simulation and experiment verification. In this study, a numerical model combining finite element method (FEM) with boundary element method (BEM) is established with consideration of two-way sequential coupling of the electromagnetic field and the structure field. In this model, the introduction of BEM for modeling air and insulator avoids FE meshing and thus enhances computational stability; air damping is considered by applying mass damping to the sheet, which reduces the ineffective long-lasting oscillation of the sheet after discharging and thus significantly improves computational efficiency. With this model, the discharge-induced stress wave is found propagating outwards from the center of the coil acting zone in the form of a sine wave; radial stresses on the top and bottom surfaces of the sheet are symmetrically distributed with respect to the axis of zero stress and attenuate along radial distance; circumferential stresses on both surfaces are negative away from the discharge acting zone. Consequently, wrinkling is attributed to circumferential stress caused by the propagation of the stress wave and the weak circumferential rigidity of the sheet, and local hump and depression are attributed to the stress concentration because of the interruption of previously formed structure on the propagation of stress wave. In light of the propagation of stress wave and energy method, a criterion for wrinkling is established and then the relations between the parameters of discharging positions, voltage and geometry of the sheet and the defects are obtained. As the result, aiming at the objective ellipsoid surface part, a well-scheduled eight-station discharging approach was established in this work. The corresponding processing parameters were determined. Then, a qualified production cycle with consistent profile is determined by comparison of simulation and experiment. Therefore, this study provides a way for forming process design of large-size thin-walled sheet components with EMIF.

On the Forming Uniformity During a Single Layer Forming of Electromagnetic Incremental Forming

Electromagnetic Incremental Forming of Integral Panel under Different Discharge Conditions

Study on forming uniformity of multi-electromagnetic forming (EMF) of aluminum sheet metal

Analysis of Forming Defects in Electromagnetic Incremental Forming of a Large-Size Thin-Walled Ellipsoid Surface Part of Aluminum Alloy

An Electromagnetic Incremental Forming (EMIF) Strategy for Large-Scale Parts of Aluminum Alloy Based on Dual Coil

Dependence on Forming Parameters of an Integral Panel During the Electromagnetic Incremental Forming Process

Electromagnetic Incremental Forming (EMIF): A Novel Aluminum Alloy Sheet and Tube Forming Technology

Investigation of Accurate Forming of a Semi-Ellipsoidal Shell Part by an Electromagnetic Forming Method

Mechanisms and Forming Rules of Large Thin-Walled Aluminum Alloy Components in Electromagnetic Incremental Forming

Large-scale Sheet Deformation Process by Electromagnetic Incremental Forming Combined with Stretch Forming

Improving Forming Accuracy of Variable-Diameter Tube by Electromagnetic Forming Using Segmented Coil

Two-step electromagnetic forming: A new forming approach to local features of large-size sheet metal parts

Large ellipsoid parts manufacture using electromagnetic incremental forming with variable blankholder structure

Improvement on formability and forming accuracy in electromagnetic forming of deep-cavity sheet metal part using a dual-coil system

A Method to Improve Forming Accuracy in Electromagnetic Forming of Sheet Metal

Coil-less electromagnetic forming process with uniform-pressure characteristics for shaping sheet metals

Investigation of Large Sheet Deformation Process in Electromagnetic Incremental Forming

The Research of Electromagnetic Incremental Forming Process of Aluminum Alloy Sheet and the Interaction Between the Die and the Sheet

Investigation of Dynamic Deformation Behaviour of Large-Size Sheet Metal Parts under Local Lorentz Force

Inhomogeneous Deformation Behaviors of Oblique Hole-Flanging Parts During Electromagnetic Forming

Numerical Study on Electromagnetic Hydraulic Forming Process to Overcome Limitations of Electromagnetic Forming Process