Abstract:Conventionally, cathode current collectors for lithium-ion batteries (LIB) consist of an aluminum foil generally manufactured by a rolling process. In the present work, a novel one-step manufacturing method of structured aluminum foil current collectors for lithium-ion batteries by electroforming is introduced. For this, a low-temperature chloride-based ionic liquid was used as an electrolyte and a rotating cylinder out of stainless steel as a temporary substrate. It was shown that the structure of the aluminum foils can be adjusted from dense and flat to three-dimensional by choosing an appropriate substrate rotation speed and current density. Scanning electron microscopy (SEM) and white light interferometry (WLI) were utilized to analyze the foils’ surface morphology, structure and topography. The SEM analysis of the aluminum foils showed that the rolling process produced a foil with small grains, while electrodeposition resulted in foils with different degrees of grain growth and seed formation. This was in total agreement with WLI results that revealed significant differences in terms of roughness parameters, including the peak-to-valley difference Rpv, the root-mean-square roughness Rq and the arithmetic mean roughness Ra. These were, respectively, equal to 6.8 μm, 0.35 μm and 0.279 μm for the state-of-the-art foil and up to 96.6 μm, 10.92 μm and 8.783 μm for the structured electroformed foil. Additionally, cyclic voltammetry (CV) of the aluminum foils was used to investigate their passivation behavior within the typical LIB cathode potential operation window. The strong decrease in the current density during the second cycle compared to the first cycle, where an anodic peak appeared between 4.0 and 4.4 V vs. Li/Li+, demonstrated that passivation occurs in the same manner as observed for commercial Al current collectors.

Electrodeposition of Aluminium Foils on Carbon Electrodes in Low Temperature Ionic Liquid

Electrodeposition of Al foil for the collector of lithium-ion batteries by electrorefining in [Emim]Cl-AlCl 3 ionic liquid with O 2− ion at room temperature: Electrochemical dissolution behavior of Al anode

Electrodeposition of Aluminum on Stainless Steel from Room Temperature Molten Salts

Electrodeposition and Corrosion Behavior of Nanocrystalline Aluminum from A Chloroaluminate Ionic Liquid

Electrodeposition of aluminum on rare earth alloy surface in room temperature molten salts

Anodic behavior in AlCl3-EMIC ionic liquid of Ti6Al4V alloy and its application for enhancing the adhesion strength of aluminum coatings

Formation of aluminide coatings by low-temperature heat treatment of Al coating electrodeposited from ionic liquid

Effects of Refinement by Al Wires on the Al-deposition from AlCl3-EMIC at Room Temperature

Viscous Layer Formed in the Anodic Electrolytic Etching of Reactive Metals in Ionic Liquid

Corrosion Resistance of Electrodeposited Aluminum Coating on NdFeB Magnet from AlCl_3-EMIC Ionic Liquid

Double layer, diluent and anode effects upon the electrodeposition of aluminium from chloroaluminate based ionic liquids

Anodic behavior of Fe in acidic AlCl3-EMIC ionic liquid

Electrodeposition of aluminum–magnesium alloys from an aluminum-containing solvate ionic liquid at room temperature

Electroforming as a Novel One-Step Manufacturing Method of Structured Aluminum Foil Current Collectors for Lithium-Ion Batteries

Substrate and current density effects on electrodeposited aluminium coatings

Electrolytic Etching of AZ91D Mg Alloy in AlCl3–EMIC Ionic Liquid for the Electrodeposition of Adhesive Al Coating

Preparation of Aluminide Coatings on the Inner Surface of Tubes by Heat Treatment of Al Coatings Electrodeposited from an Ionic Liquid

Anodic Dissolution of Aluminum in the Aluminum Chloride-1-Ethyl-3-methylimidazolium Chloride Ionic Liquid

Anodic dissolution of aluminum in AlCl3-[BzMIM]Cl ionic liquid

Effect of Potential on Aluminium Early-Stage Electrodeposition Onto Ndfeb Magnet

Simulation of aluminium electrodeposition on complex geometry: Influence of input parameters and electrodeposition conditions