Abstract:The design progress of the Radio Frequency Quadrupole (RFQ) accelerator for the Compact Pulsed Hadron Source (CPHS) at Tsinghua University is presented in this paper. The RFQ will accelerate protons from 50 keV to 3 MeV, with the RF frequency of 325 MHz. The objective is to obtain the optimum structure of the RFQ accelerator with high transmission rate and tolerable total length. The beam dynamics are studied by the simulation of the proton beam in the RFQ accelerator with the code of PARMTEQM. The output proton beam from the RFQ is well matched into the DTL without Medium-Energy-Beam-Transport (MEBT) between the RFQ and DTL. INTRODUCTION A 325 MHz Radio Frequency Quadrupole (RFQ) accelerator will be built to produce 50mA of proton beam at 3 MeV as an injector of the 13 MeV DTL for the Compact Pulsed Hadron Source (CPHS) project at Tsinghua University. The CPHS project is a universitybased proton accelerator platform (13 MeV, 16 kW, peak current 50 mA, 0.5 ms pulse width at 50 Hz) for multidisciplinary neutron and proton applications [1]. The RFQ system consists of three four-vane resonant cavity sections, one power coupler, 47 slug tuners, 8 dipole-mode stabilizer rods, the RF power supply and its low-level control, vacuum, water cooling, resonance control, beam diagnostics, support and alignment systems. Fig. 1 shows the sketch of the RFQ system and the design parameters are listed in Table 1. Figure 1: Sketch of the 3 MeV RFQ for the CPHS project. To save space and cost, no Medium-Energy-BeamTransport (MEBT) will be placed between the RFQ and DTL. The RFQ is carefully designed to match the beam from the high-energy end of the RFQ to the entrance of the DTL, by reducing the focusing in the exit of the RFQ. The cavity cross section and vane-tip geometry are tailored as a function of longitudinal position. The physics design has been completed. One test section made by aluminium has been machined to verify the capability of the numerically controlled milling machine. The final RFQ cavity is now under construction. This paper summarizes the current physics and mechanical design of the CPHS RFQ and presents the fabrication status of the test section. Table 1: Design Parameters of the CPHS RFQ Parameters Value Unit

PHYSICAL DESIGN OF 4 MeV / 2 . 5 ACCELERATOR *

Development of A C-Band 6 Mev Standing-Wave Linear Accelerator

Design, Fabrication, and Testing of an X-band 9-Mev Standing-Wave Electron Linear Accelerator

Physical design of a compact 2 MeV deuteron radio-frequency quadrupole

Design and beam dynamics simulation of an 8 MeV compact accelerator-driven neutron source

DEVELOPMENT OF THE 3 MeV RFQ FOR THE COMPACT PULSED HADRON SOURCE AT TSINGHUA

Development of the 3MeV RFQ for the compact pulsed hadron source at tsinghua university

Tuning and Cold Test of A Four-Vane Rfq with Ramped Inter-Vane Voltage for the Compact Pulsed Hadron Source

R&D STATUS OF A 3.5MEV RFQ ACCELERATOR FOR ADS STUDY IN CHINA

The Design of a High-Intensity Deuteron Radio Frequency Quadrupole Accelerator

Prototype of Multi-Filament Electron Curtain Accelerator

Detuned-Structure-Based Beam-Driven Accelerator

Design,fabrication,and Testing of Low-Group-velocity S-band Traveling-Wave Accelerating Structure

Design of the CPHS RFQ Linac at Tsinghua University

Design, fabrication, and cold test of an S-band high-gradient accelerating structure for compact proton therapy facility

Development of High Power Irradiating Accelerator

Fabrication, Tuning, and High-Gradient Testing of an X-band Traveling-Wave Accelerating Structure for VIGAS

Design of a 4 MeV/u IH-DTL Injector for Cancer Therapy

Study and Design of the Coupled Cavity with Ladder RFQ and IH DTL Structure for Transportable Neutron Source

A 3-Mev RFQ Accelerator for the Compact Pulsed Hadron Source at Tsinghua University

An X-band Disk-and-washer Accelerating Structure for Electron Accelerators