Abstract:An experimental investigation was conducted to quantify the dynamic ice accretion and the unsteady heat transfer process over the ice accreting surfaces of composite-based airframes widely used for light-weight, Unmanned-Aerial-Systems (UAS), in comparison to those over the surfaces of metal based airframes used by conventional manned aircraft, in order to elucidate the underlying icing physics specifically pertinent to UAS inflight icing phenomena. Two airfoil/wing models with the same airfoil shape, but made of different materials (i.e., thermoplastic material with the thermal conductivity being only similar to 0.2 W/m.K to represent typical UAS airframe substrates vs. Aluminum with the thermal conductivity being similar to 200 W/m.K widely used for conventional manned aircraft). The two test models were mounted side-by-side inside an Icing Research Tunnel available at Iowa State University (i.e., ISU-IRT) under the same wet glaze or dry rime icing condition. During the icing experiment, while a high-speed imaging system was used to record the dynamic ice accretion process over the surfaces of the test models, an infrared thermal imaging system was also used to map the corresponding surface temperature distributions over the ice accreting airfoil surfaces. It was found that, upon the impacting of the airborne, super-cooled water droplets in ISU-IRT, ice would start to accrete rapidly on the surfaces of the test models with a significant amount of the latent heat of fusion being released associated with the phase changing of the impacted super-cooled water mass over the airfoil surfaces. The thermal conductivity of the airframe substrate was found to affect the dynamic ice accretion and unsteady heat transfer processes over the ice accreting surfaces significantly. With the two test models being exposed under the same icing conditions, the released latent heat of fusion was found to be dissipated much slower over the surface of the thermoplastic model, due to the much lower thermal conductivity of the thermoplastic substrate. In comparison with those on the surface of the Aluminum model, the slower dissipation of the released latent heat of fusion on the surface of the thermoplastic model was found to cause higher surface temperatures and greater "heated" regions near the airfoil leading edge, more obvious surface water run-back over the airfoil surface, and formation of more complex rivulet-shaped ice structures at further downstream locations beyond the direct impinging zone of the super-cooled water droplets. (C) 2018 Elsevier Ltd. All rights reserved.

An Experimental Study on the Transient Ice Accretion Process over the Blade Surfaces of a Rotating UAS Propeller

Experimental Investigation on the Dynamic Icing Process over a Rotating Propeller Model

An Experimental Study on the Aerodynamic Performance Degradation of a UAS Propeller Model Induced by Ice Accretion Process

An Experimental Study of Surface Wettability Effects on Dynamic Ice Accretion Process over an UAS Propeller Model

Effects of Ice Accretion on the Aerodynamic Performance and Wake Characteristics of an UAS Propeller Model

An Experimental Study on the Effects of Surface Wettability on the Ice Accretion over a Rotating UAS Propeller

Wind Tunnel Test and Numerical Computation on Ice Accretion on Blade Airfoil for Straight-bladed VAWT

An Experimental Investigation of Dynamic Ice Accretion Process on a Wind Turbine Airfoil Model Considering Various Icing Conditions

High-Speed Imaging to Quantify the Transient Ice Accretion Process on a NACA 0012 Airfoil

An Experimental Investigation on the Dynamic Glaze Ice Accretion Process over a Wind Turbine Airfoil Surface

An Experimental Study on Dynamic Ice Accretion Process over the Surfaces of Rotating Aero-Engine Spinners

An Experimental Investigation on the Unsteady Heat Transfer Process over an Ice Accreting NACA 0012 Airfoil

An experimental study on the aerodynamic performance degradation of a wind turbine blade model induced by ice accretion process

An Experimental Investigation on the Dynamic Ice Accretion and Unsteady Heat Transfer over an Airfoil Surface with Embedded Initial Ice Roughness

Effects of thermal conductivity of airframe substrate on the dynamic ice accretion process pertinent to UAS inflight icing phenomena

Ice accretion characteristics on rotating aeroengine fan blades

Numerical Simulation of Icing on the Rotating Blade

Experimental Study on the Effects of Substrate Hydro-/Icephobicity on Ice Mitigation and Ice Shedding During the Dynamic Icing Process over the Rotating Propeller of an Unmanned-Aerial-Vehicle

An Experimental Investigation on the Convective Heat Transfer Process over an Ice Roughened Airfoil

Experimental Investigation on Ice Accretion on a Rotating Aero-Engine Spinner with Hydrophobic Coating

An experimental investigation on the unsteady heat transfer process over an ice accreting airfoil surface