Abstract:Adding conductive fillers to an insulating polymer matrix produces composites with unique properties. Varying amounts of carbon black (0.33, 0.67, and 1 wt%) and graphene nanoplatelets (5, 10, 15, and 20 wt%) were added to epoxy. In addition, a few carbon black/graphene nanoplatelet/epoxy formulations were also fabricated. The conductivity and tensile properties were determined and analyzed. The single filler composites containing 5 and 10 wt% graphene nanoplatelet and 0.33 wt% carbon black could be used for electrically insulating applications. Composites containing 15 and 20 wt% graphene nanoplatelet could be used for static dissipative applications. The following composites could be used for semi-conductive applications: 0.67 wt% carbon black/epoxy, 1 wt% carbon black/epoxy, 0.33 wt% carbon black/5 wt% graphene nanoplatelet/epoxy, and 0.33 wt% carbon black/10 wt% graphene nanoplatelet/epoxy. At the 95% confidence level, the combination of 0.33 wt% carbon black with 5 wt% graphene nanoplatelet caused the composite electrical resistivity (1/electrical conductivity) to significantly decrease from ∼10 15 ohm-cm to ∼10 4 ohm-cm. It is likely that the highly branched, high surface area carbon black is forming an electrically conductive network with graphene nanoplatelets. Concerning single filler composites, adding ≤1 wt% carbon black did not significantly lower the composite tensile strain; however, adding graphene nanoplatelet did decrease tensile strain and increase modulus. One possible application for the 10 wt% graphene nanoplatelet/epoxy composite is in Polymer Core Composite Conductors for power transmission lines, which need to be electrically insulating, have improved thermal conductivity (increased from 0.2 to 0.3 W/m-K), increased tensile modulus (increased from 2.7 to 3.3 GPa), and good tensile strength (70 MPa) and strain (3.3%).

ELECTRICAL CONDUCTIVITY, DIELECTRIC PERMITTIVITY AND DYNAMIC MECHANICAL PROPERTIES OF GRAPHENE/EPOXY NANOCOMPOSITES

Nonlinear Conductive Behaviors of Multilayer Graphene Nanosheets/Epoxy Composites below the Percolation Threshold

Electrical Properties of Epoxy-Based Nanocomposites Filled with Graphene Oxide

Dielectric Properties of Graphene-Filled Epoxy Nanocomposite with Enhanced Thermal Conductivity

Enhanced Thermal Conductivity and Dielectric Properties of Epoxy Composites with Fluorinated Graphene Nanofillers

Molecular Dynamics Simulation of Key Physical Properties of Graphene Oxide / Epoxy Resin Nanocomposite Dielectrics

Molecular Dynamics Simulation on Dielectric Constant and Thermal Conductivity of Crosslink Epoxy/functionalized graphene Nano-composites

Interface Probing by Dielectric Frequency Dispersion in Carbon Nanocomposites

Self-networking of graphene in epoxy resin based on thermal induced dynamic chemical network

Dielectric Properties of Epoxy-Al2o3 Nanocomposites

Dielectric Studies of Al Nanoparticle Reinforced Epoxy Resin Composites

Structural, Dynamic Mechanical and Dielectric Properties of Mesoporous Silica/epoxy Resin Nanocomposites

Dielectric, low‐frequency noise and mechanical properties of hybrid carbon nanotubes/graphene nanoplatelets epoxy composites

Tensile and conductivity properties of epoxy composites containing carbon black and graphene nanoplatelets

Correlation of Electrical Conductivity, Dielectric Properties, Microwave Absorption, and Matrix Properties of Composites Filled with Graphene Nanoplatelets and Carbon Nanotubes

Preparation and properties of carbon‐based epoxy nanocomposites: Dynamic mechanical, dielectric, and thermal properties

Improved Mechanical and Dielectric Performances of Epoxy Nanocomposites Filled with Aminated Polyethylene Glycol Grafted Graphene

Electrical Properties of Epoxy/Graphite Flakes Microcomposite at the Percolation Threshold Concentration

Temperature-Dependent Dielectric Properties of Al/Epoxy Nanocomposites

Simultaneously Improved Toughness and Dielectric Properties of Epoxy/Graphite Nanosheet Composites

Graphene–Epoxy Composites with High Dielectric Constant Prepared by Cryomilling