Abstract:Black phosphorus has attracted broad interest because of their low-dimensional effect, and has become a new kind of two-dimensional (2D) materials. Phosphorus has several allotropes. Black phosphorus is the most thermodynamic stable in them. As a kind of two-dimensional materials, black phosphorus has high carrier mobility and on/off ratio. The band gap of black phosphorus can be adjusted by its number of layers from 0.3 to 2 eV. It is of great significance to the development of new infrared and near-infrared optoelectronic devices. Currently, the main methods for preparing black phosphorus are chemical vapor transfer and high energy ball milling methods. In this paper, black phosphorus was successfully synthesized from red phosphorus via chemical vapor transfer and high energy ball milling methods. Then black phosphorus was put in ethanol for 10 min to liquid exfoliation, in which the ultrasonic power was 400 W. The microstructures and stability of black phosphorus synthesized by two methods were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimeter (DSC). In situ electrical measurements of black phosphorus prepared by chemical vapor transfer were performed using a commercial scanning tunnelling microscope-transmission electron microscope probing system (STM-TEM, Nanofactory Instruments) inserted into a JEOL-2010F TEM. The microstructural characterization results show that there is some red phosphorus and amorphous phases in black phosphorus prepared by high energy ball milling method. On the contrary, the black phosphorus prepared by chemical vapor transfer method has no amorphous phases. The XRD results show that black phosphorus synthesized by chemical vapor transfer method did not change significantly after keeping in the air for 16 days. The DSC results show that the volatile points of the black phosphorus prepared by high energy ball milling and chemical vapor transfer methods are respectively 394.5 and 432.2 degrees C, which means the latter has better thermal stability. The TEM results show that a layer or two layers of phosphorene via liquid exfoliation had been obtained, which is large in size and clean in surface. After being irradiated in TEM with a dose of 0.8 eV/(angstrom(2).s) at 200 kV for 60 min, few new diffraction spots appeared in black phosphorus synthesized by chemical vapor transfer method, which indicates it is relatively stable under electron radiation in vacuum. In a word, the black phosphorus prepared by chemical vapor transfer method has large size, good crystallinity, high purity, and high stability. It can be used to prepare two-dimensional black phosphorus by mechanical exfoliation and liquid exfoliation, and then be applied to advanced microelectronic devices.

Preparation of Few-Layer Black Phosphorus by Wet Ball Milling Exfoliation

An Ultrahigh Pressure Homogenization Technique for Easily Exfoliating Few-Layer Phosphorene from Bulk Black Phosphorus

Degradation Chemistry and Stabilization of Exfoliated Few-Layer Black Phosphorus in Water.

Ultrafast Cathodic Exfoliation of Few-Layer Black Phosphorus in Aqueous Solution

Liquid Exfoliation of Solvent-Stabilized Few-Layer Black Phosphorus for Applications Beyond Electronics.

Wet Chemical Method for Black Phosphorus Thinning and Passivation.

Solvent Exfoliation of Electronic-Grade, Two-Dimensional Black Phosphorus

Growth mechanism of black phosphorus synthesized by different ball milling techniques

Production of High-Quality and Large Lateral-Size Black Phosphorus Nanoparticles/nanosheets by Liquid-Phase Exfoliation

Preparation Of Large Size, Few-Layer Black Phosphorus Nanosheets Via Phytic Acid-Assisted Liquid Exfoliation

Large-Scale, Highly Efficient, and Green Liquid-Exfoliation of Black Phosphorus in Ionic Liquids.

Ultrafast Electrochemical Expansion of Black Phosphorus Toward High-Yield Synthesis of Few-Layer Phosphorene

Liquid-phase exfoliation of black phosphorus and its applications

Study on Black Phosphorus Characteristics Using a Two-Step Thinning Method

Facile synthesis of black phosphorene via a low melting media assisted ball milling

Progress in the synthesis of 2D black phosphorus beyond exfoliation

Identification of Lattice Oxygen in Few-Layer Black Phosphorous Exfoliated in Ultrahigh Vacuum and Largely Improved Ambipolar Field-Effect Mobilities by Hydrogenation and Phosphorization

Exfoliation of Few-Layer Black Phosphorus in Low-Boiling-Point Solvents and Its Application in Li-Ion Batteries

Preparation and Characterization of Black Phosphorus

Electrochemical exfoliation of two-dimensional layered black phosphorus and applications

Preparation and Formation Mechanism of Few-Layer Black Phosphorene Through Liquid Pulsed Discharge