Application of four different models for predicting the high-temperature flow behavior of TG6 titanium alloy

Renhai Yu,Xue Li,Wenjun Li,Jintong Chen,Xin Guo,Jinghui Li

DOI: https://doi.org/10.1016/j.mtcomm.2020.102004

IF: 3.8

2021-03-01

Materials Today Communications

Abstract:<p>The high-temperature flow behavior of TG6 titanium alloy at strain rates from 0.001 to 10 s^-1 and temperatures from 850-1050 ℃ was systematically studied by Gleeble-3500 thermal simulation compressor, and four different constitutive equations (classical Arrhenius (AR) model, modified Johnson-Cook (MJC) model, modified Zerilli–Armstrong (MZA) model, artificial neural network (ANN) model) were derived. EBSD results show that the deformation behavior of TG6 titanium alloy has flow softening characteristics. Furthermore, the calculated correlation coefficient (R) and average absolute relative error (AARE) are used to make an error analysis of the fit accuracy of the above models to evaluate the predictive ability of the TG6 titanium alloy flow behavior. The results of the comprehensive analysis are as follows: on the one hand, it is revealed that different predictive capabilities of the high-temperature flow behavior of TG6 titanium alloy by all the four models based on the meticulous experimental comparison and validation (AR model: R² is 97.376% and AARE is 14.16%; MJC model: R² is 97.42% and AARE is 18.5%; MZA model: R² is 90.598% and AARE is 19.32%; ANN model: R² is 99.94% and AARE is 2.14%), but MZA model is a special case. On the other hand, the MJC and AR model can be considered as the best choices for relatively accurate description and prediction of the flow stress behavior of TG6 titanium alloy when the predictability of the model and the material parameters to be considered.</p>

materials science, multidisciplinary

What problem does this paper attempt to address?

The paper primarily investigates the high-temperature flow behavior of TG6 titanium alloy under different strain rates (0.001 to 10 s⁻¹) and temperatures (850 to 1050 ℃). The study systematically examines the flow behavior under these conditions using the Gleeble-3500 thermal simulation compression system and establishes four different constitutive equation models based on experimental data: the classical Arrhenius (AR) model, the modified Johnson-Cook (MJC) model, the modified Zerilli-Armstrong (MZA) model, and the artificial neural network (ANN) model.

The main objectives of the paper are:
1. **Study the flow behavior of TG6 titanium alloy at high temperatures**: Understand the flow softening characteristics of TG6 titanium alloy under different strain rates and temperature conditions.
2. **Establish constitutive equation models**: Compare the predictive capabilities of the four models for the high-temperature flow behavior of TG6 titanium alloy and select the most suitable model to describe its flow stress behavior.
3. **Evaluate model predictive capabilities**: Use the correlation coefficient (R) and average absolute relative error (AARE) to compare and analyze the fitting accuracy of the models to evaluate their predictive capabilities.

The study found that:
- The predictive capabilities of the four models for the high-temperature flow behavior of TG6 titanium alloy vary (AR model: R²=97.376%, AARE=14.16%; MJC model: R²=97.42%, AARE=18.5%; MZA model: R²=90.598%, AARE=19.32%; ANN model: R²=99.94%, AARE=2.14%).
- The MZA model is a special case, while the MJC and AR models are considered more accurate choices for describing and predicting the flow stress behavior of TG6 titanium alloy.
- The artificial neural network model can very effectively establish the thermal deformation behavior of TG6 titanium alloy, with its predicted values highly consistent with the experimental values.

In summary, this study aims to deeply understand the flow behavior of TG6 titanium alloy under high-temperature conditions through experimental and modeling methods and to determine the most suitable model to describe this behavior, which has important guiding significance for the subsequent engineering applications of the material.