Abstract:Two fluorescent high‐performance polymers based on dicyanoarylamine luminogens were readily synthesized via polycondensation. Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive in both solution and solid film states, thereby demonstrating the aggregation‐induced fluorescence changes. Introduction Fluorescent high‐performance polymers have been extensively used in designing optoelectronic devices due to their low cost, excellent thermal stability, high mechanical strength, low flammability, good chemical and radiation resistance, and good electronic properties. While conventional organic luminophores fluoresce strongly in dilute solutions, they suffer from undesirable aggregation‐caused quenching in concentrated solutions and in the solid state due to extensive π‐π stacking interactions and formation of delocalized excitons or excimers. This phenomenon leads to non‐radiative decay thus, decreased fluorescence emission of the material in the solid film state, which significantly limits their real‐world application as solid light‐emitting materials. Objectives To develop new high‐performance polymers with high photo luminescent efficiency, good processability, film‐forming properties, which could potentially be used in the fabrication of optoelectronic devices. Methods The preparation of the polyimide DiCN‐PI was carried out by a one‐step, high‐temperature solution imidization method. In this procedure, 1,2,4,5‐cyclohexanetetracarboxylic dianhydride and the diamine were polymerized in 1‐methyl‐2‐pyrrolidinone and γ‐butyrolactone co‐solvent at 180°C for 15 hours in the presence of isoquinoline as catalyst. On the other hand, polyamide DiCN‐PA was synthesized according to the direct phosphorylation polycondensation technique described by Yamazaki from diamine and trans‐1,4‐cyclohexanedicarboxylic acid using triphenyl phosphite and pyridine as condensing agents. Results and Discussion Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive with PL emission bands around 555 (bluish‐green) and 498 (cyan) nm in dilute 1‐methyl‐2‐pyrrolidinone solutions for polyimide and polyamide, respectively. In the solid film state, the polymers emit light green and yellow colors, which simulate the PL behavior of their aggregated states, thereby demonstrating aggregation‐induced fluorescence changes. Conclusions These results indicate that the incorporation of bulky dicyanoarylamine moiety and alicyclic monomer units into the rigid polymer backbones effectively disrupted the planarity of the chain packing which resulted to the fluorescent high‐performance polymers with desired properties for potential optoelectronic applications.

Preserving High-Efficiency Luminescence Characteristics of an Aggregation-Induced Emission-Active Fluorophore in Thermostable Amorphous Polymers

The Progress of Nonconjugated Photoluminescent Polymers

High Efficiency Luminescent Liquid Crystalline Polymers Based on Aggregation-Induced Emission and “jacketing” Effect: Design, Synthesis, Photophysical Property, and Phase Structure

High-Efficiency Long-Wavelength Fluorescent Hyperbranched Polysiloxanes: Synthesis, Emission Mechanism, Information Encryption, and Film Preparation

What makes efficient circularly polarised luminescence in the condensed phase: aggregation-induced circular dichroism and light emission

Significantly Red-Shifted Emissions of Nonconventional AIE Polymers Containing Zwitterionic Components

High solid-state efficiency fluorescent main chain liquid crystalline polytriazoles with aggregation-induced emission characteristics

Emission mechanism understanding and tunable persistent room temperature phosphorescence of amorphous nonaromatic polymers

Controlling the Fluorescence Performance of AIE Polymers by Controlling the Polymer Microstructure

Assembly, Stabilities, and Photophysical Behaviors of Highly Efficient Luminescent Materials Fabricated from a Terbium Complex Doped Silica/polymer Hybrids

Effective Suppression of Intra- and Interchain Triplet Energy Transfer to Polymer Backbone from the Attached Phosphor for Efficient Polymeric Electrophosphorescence

Enabling Efficient and Ultralong Room-Temperature Phosphorescence from Organic Luminogens by Locking the Molecular Conformation in Polymer Matrix

Synthesis, characterization, and photophysical properties of dicyanoarylamine‐based semi‐aromatic polymers

Using Fluorine-Containing Amphiphilic Random Copolymers To Manipulate The Quantum Yields Of Aggregation-Induced Emission Fluorophores In Aqueous Solutions And The Use Of These Polymers For Fluorescent Bioimaging

Heat-Resistant Polymers with Intense, Visible Photoluminescence Functionality and Fluorescence Probing Application

Photoinduced Radical Persistent Luminescence in Semialiphatic Polyimide System with Temperature and Humidity Resistance

Using Tetraphenylethene and Carbazole to Create Efficient Luminophores with Aggregation-Induced Emission, High Thermal Stability, and Good Hole-Transporting Property

Tuning the Fluorescence of Aggregates for End-Functionalized Polymers Through Varying Polymer Chains with Different Polarities

Highly Efficient Luminescence from a Red Thermally Activated Delayed Fluorescence Emitter with Flexible Conformation of Ancillary Groups.

Light‐driven and Aggregation‐induced Emission from Side‐chain Azoindazole Polymers

Amide Cluster Induced and Hydrogen Bonding Regulated Luminescence of Linear Aliphatic Polyamide 1212 with Long Alkane Chain