Abstract:Poly(3,4-ethylenedioxythiophene): poly (styrenesulfonic acid) (PEDOT: PSS) is one of the most successful conductive polymers, usually used as hole injecting layer in organic light-emitting devices. Due to low conductivity and unsatisfied work function (WF), the modification of PEDOT:PSS with some additives has been proved to be cost-effective. Perfluorinated ionomer (PFI) has been reported as an effective additive to improve the WF of PEDOT:PSS, increasing from 5.2 eV to 5.95 eV with a recipe of PEDOT(1):PSS(6):PFI(25). However, the strong hydrophobicity of PFI has limited the choice of the organic solvents used to fabricate the uniform emitting layer on the modified PEDOT:PSS. To address this issue, the polymers were introduced as the additive of the emitter to overcome the non-uniform morphology on the hydrophobic surface of PEDOT:PSS:PFI. A conventional fluorescent polymer poly(9-vinylcarbazole) (PVK) and a thermally activated delayed fluorescent polymer (4-(2-(9-(heptadecan-9-yl)-6-phenyl-9H-carbazol-3-yl)-9,9-dihexyl-7-phenylacridin-10(9H)-yl)phenyl) (phenyl)methanone (PABPC2.5) were compared in parallel to reveal the influence of the polymer additive of the emitters on the overall performances of the devices. The control devices based on the PFI-modified PEDOT:PSS achieved a maximum current efficiency (CE) of 0.14 cd A-1, without any polymer additives in the emitting layer. In contrast, the CE of the devices with PVK and PABPC2.5 were dramatically elevated to 7.1 cdA-1 and 4.5 cd A-1 respectively, when a small molecular thermally activated delayed fluorescence was employed as the emitter. Enabled by a easily soluble phosphorescent emitter acetylacetonatobis(4-(4-tert-butylphenyl)-thieno[3,2-c]pyridinato-C2,N)iridium (PO-01-TB). The device with PABPC2.5 as the additive obtained a maximum CE of 42.0 cd A-1, which is significantly higher than 15.7 cd A-1 of the one with the additive PVK, attributed to the energy transfer in the emitting layer. The polymer additives not only overcome the issue of the hydrophobicity of the modified PEDOT:PSS but endow the exciton harvesting from the polymer to the small molecular emitters.

Effective Suppression of Intra- and Interchain Triplet Energy Transfer to Polymer Backbone from the Attached Phosphor for Efficient Polymeric Electrophosphorescence

Synthesis and performances of chelating electrophosphorescent polymers based on different ancillary ligands

New Iridium Complex As High-Efficiency Red Phosphorescent Emitter in Polymer Light-Emitting Devices

Electrophosphorescent Polymers Based on Poly(para-phenylene)s Grafted with Ir Complex on Side Chain

Application of Heteroleptic Iridium Complexes with Fluorenyl-Modified 1-Phenylisoquinoline Ligand for High-Efficiency Red Polymer Light-Emitting Devices

Suppression of Efficiency Roll-off in Highly Efficient Blue Phosphorescent Organic Light-Emitting Devices Using Novel Iridium Phosphors with Good Electron Mobility

Effective shielding of triplet energy transfer to conjugated polymer by its dense side chains from phosphor dopant for highly efficient electrophosphorescence.

Synthesis and Properties of Electrophosphorescent Chelating Polymers with Iridium Complexes in the Conjugated Backbone.

Energy transfer and triplet exciton confinement in polymeric electrophosphorescent devices

Efficient and Low-Efficiency-roll-off Near-Infrared (NIR) Polymer Light-Emitting Diodes (pleds) Based on an Asymmetric Binuclear Iridium(iii)-Complex

Facilitating triplet energy-transfer in polymetallayne-based phosphorescent polymers with iridium(III) units and the great potential in achieving high electroluminescent performances

Iridium Complexes Embedded into and End-Capped Onto Phosphorescent Polymers: Optimizing PLED Performance and Structure–property Relationships

Enhancement of Phosphorescence of Ir Complexes Bound to Conjugated Polymers: Increasing the Triplet Level of the Main Chain

Improving the Performance of Phosphorescent Polymer Light-Emitting Diodes Using Morphology-Stable Carbazole-Based Iridium Complexes

Efficient Saturated Red Light-Emitting Polyfluorenes Containing Iridium Complexes in Side Chains

High Triplet Energy Polymer As Host For Electrophosphorescence With High Efficiency

Highly Efficient Energy Transfer System of Phosphorescence Dye/Board Band Gap Semiconductor Polymer

Thermally activated delayed fluorescent polymer- assisted morphological control on perfluorinated ionomer enriched surface and exciton harvesting for phosphorescent organic light-emitting devices

Synthesis and Properties of Electrophosphorescent Conjugated Polymers Containing Iridium Complexes in Polymer Backbone

High-efficiency red-light emission from polyfluorenes grafted with cyclometalated iridium complexes and charge transport moiety.

Efficient Red Phosphorescent Polymers with Trap-Assisted Charge Balance: Molecular Design, Synthesis, and Electroluminescent Properties