Abstract:Present studies include a series of investigations on microfluidics from fabrication to application. In the application this study focuses on some fundamental problems regarding the manipulation of droplets and bubbles inside microfluidics, including the size control during generation, the critical condition for breaking droplets, chaotic mixing inside moving droplets and nanofluids synthesis.A low-cost fabrication method for manufacturing glass-based microfluidic devices is developed in a routine laboratory without the requirement of a clean room. Direct bonding of glass material is realized without using any additives. The fabrication method is very reliable and the yield is larger than 90%. Channel surface modification from hydrophilic to hydrophobic is realized inside the microfluidic devices after fabrication. With the help of the surface modification, both of the two types of droplets, oil-in-water and water-in-oil, can be generated inside glass-based microfluidic devices.Droplet formation under controlled flow rates and bubble formation under controlled pressures in confined T-shaped junctions are experimentally investigated by changing thermophysical properties of continuous phases and by changing the controlled dynamic parameters. A pressure-driven mechanism of droplet/bubble formation is experimentally discovered. The influence of the continuous phase thermophysical properties and the controlled dynamic parameters on droplet/bubble volume and formation time is systematically investigated. Empirical correlations are obtained for predicting the droplet volume and formation time.Droplet breakup in either symmetrically or asymmetrically confined T-shaped junctions is experimentally studied. The critical condition with which microfluidic droplets will break equally is theoretically analyzed based on the pressure-driven mechanism. A semi-empirical correlation is obtained for predicting the equal breakup in symmetric T-shaped junctions. Besides the equal breakup, a new droplet breakup pattern, unequal breakup, is observed in the symmetric T-shaped junction. In asymmetric T-shaped junctions the droplet breakup is found to be very difficult.Scaling analysis of the chaotic mixing inside moving droplets is conducted based on the idealized recirculating flow and the Baker's transformation. Experimental investigations on the mixing efficiency inside the droplets moving in curved microchannels are performed with the help of the micro visualization system. It is found that the mixing efficiency is significantly enhanced by the chaotic advection inside the moving droplets and the full mixing time can be reasonably estimated by the scaling analysis. A significant mixing enhancement during the droplet formation process is observed, which is not so frequently reported by others. An effective microstructure is designed for mixing two or more individual droplets after their formation.Synthesis of copper nanofluids is realized in microfluidic reactors. In contrast to the traditional method, the copper nanofluids synthesized in the microfluidic reactors have a narrower size distribution. The synthesis time is also reduced by one order of magnitude. It is also found that the particle size and size distribution are insensitive to the flow rate of reactants, the reactants concentration and the surfactant concentration.

Intensification of Chemical Separation Engineering by Nanostructured Channels and Nanofluidics: from Theories to Applications

Emerging Abnormal Phenomena in Confined Nanofluidics

Effect of Ultrasonic Intensification on Synthesis of Nano-Sized Particles with an Impinging Jet Reactor

Analysis with fields/fluids and separation process intensification

Mass Transfer and Chemical Properties of Nano-Micron Fluids

Special Issue on Multiphase Flows in Microfluidics: Fundamentals and Applications

Fabricating Technologies of Nanofluidic Chips and Their Applications

Bio-inspired nanochannels: fabrication, modification and bioanalytical applications

Nanofluidics: A New Arena for Materials Science

Principle, Fabrication and Applications of Micro-Nano Fluid Dynamics

Millifluidics, Microfluidics, and Nanofluidics: Manipulating Fluids at Varying Length Scales

Study On Characteristics Of Interface Between Multiple Laminar Streams And Application For Secondary Etching Inside Microchannels

Mass transport in nanofluidic devices

Nanoscale Fluid Mechanics and Energy Conversion

Microfluidics: Fabrication, Droplets, Bubbles and Nanofluids Synthesis

Hydrodynamics of gas-liquid microfluidics: A review

Process intensification in gas-liquid mass transfer by nanofluids: Mechanism and current status

Transport phenomena in micro-chemical engineering

Applications of Nanomaterials in Liquid Chromatography: Opportunities for Separation with High Efficiency and Selectivity.

Review article: Fabrication of nanofluidic devices.

Experimental and Numerical Study of Mixing Behavior Inside Droplets in Microchannels