Abstract:Redox flow batteries based on sodium polysulfide (Na 2 Sx) show promise due to sodium's high solubility in organic solvents (e.g., diglyme. However, when x is lower than 5, sodium polysulfide exhibits low solubility (less than 0.1 molal), limiting the nominal capacity of this redox-active material. Sodium phosphorothioate complexes, Na 2 P 2 Sx, have been reported as an alternative to Na2Sx. Incorporating phosphorus into the polysulfide structure improves their solubility in organic solvents, specifically in diglyme. This presentation will describe the synthesis and characterization of sodium phosphorothioate complexes (Na 2 P 2 S x , where x = 6, 7, 8, and 9) for nonaqueous redox flow batteries. The structure of these materials is explored using 31 P NMR and 23 Na NMR spectroscopy, Raman spectroscopy, and X-ray diffraction analysis. Overall, 31 P NMR results indicate that P 5+ is tetrahedrally coordinated in all structures and that Na-P-S compounds have a common PS 3 - moiety. Ongoing efforts are aimed at providing more precise assignments to the 31 P bands and correlating these findings with complementary structural information obtained from 23 Na NMR and Raman spectroscopy. Electrochemical properties of sodium polysulfide and sodium thiophosphate catholytes, specifically Na 2 S 8 and Na 2 P 2 S 8 , were also compared using CV. The voltammogram of Na 2 S 8 revealed two clear redox reactions in the 1.5-3 V range vs. Na/Na + due to a multi-step electron transfer process involving the S 2- /S 0 redox center. In contrast, Na 2 P 2 S 8 exhibited a larger peak separation (~2 V) and lower peak currents at a given scan rate, potentially indicating a significant activation barrier associated with the rearrangement of the thiophosphate’s polyanionic structure during reduction/oxidation. Despite the substantial voltage hysteresis, Na 2 P 2 S 8 displayed stable cycling performance, with a slight increase in peak current after 100 cycles. This behavior is consistent with measurements on RFBs containing a Na 2 P 2 S x catholyte, where an electrode activation process increased the cell’s reversible capacity, likely due to subtle changes in the electrode’s surface chemistry during repeated oxidation/reduction. Finally, preliminary flow cell measurements on Na 2 P 2 S 7 catholyte show reversible voltage profiles after the formation step with deep discharge. Overall, this presentation demonstrates that Na-P-S catholytes represent a promising material for high energy, low-cost redox flow batteries. Acknowledgements This research was conducted at Oak Ridge National Laboratory, managed by UT Battelle, LLC, for the U.S. Department of Energy (DOE) and is sponsored by the U.S. Department of Energy through the Energy Storage Program in the Office of Electricity.

Hierarchical Nano-Electrocatalytic Reactor for High Performance Polysulfides Redox Flow Batteries

Successive ionic layer adsorption and reaction–deposited copper sulfide electrocatalyst for high-power polysulfide-based aqueous flow batteries

Catalytic polysulfides immobilization within a S/C-Co-N hollow cathode obtained by nonthermal imprison route

A High‐Efficiency Mo2C Electrocatalyst Promoting the Polysulfide Redox Kinetics for Na–S Batteries

A High‐Efficiency CoSe Electrocatalyst with Hierarchical Porous Polyhedron Nanoarchitecture for Accelerating Polysulfides Conversion in Li–S Batteries

Hierarchical Porous Carbon Nanofibers Embedded with Ultrafine Nb2O5 Nanocrystals for Polysulfide-Trapping-conversion Li-S Batteries

Hierarchical porous carbon nanofibers embedded with ultrafine Nb 2 O 5 nanocrystals for polysulfide-trapping-conversion Li-S batteries

A High‐Efficiency Mo 2 C Electrocatalyst Promoting the Polysulfide Redox Kinetics for Na–S Batteries

Efficient Catalysis of Ultrathin Two-Dimensional Fe2 O3 -CoP Heterostructure Nanosheets for Polysulfide Redox Reactions

Efficient Catalysis of Ultrathin Two-Dimensional Fe2O3-CoP Heterostructure Nanosheets for Polysulfide Redox Reactions

Hierarchical S-modified Cu Porous Nanoflakes for Efficient CO2 Electroreduction to Formate.

Construction of Heterointerfaced Nanoreactor Electrocatalyst via In Situ Evolution Toward Practical Room‐Temperature Sodium–Sulfur Batteries

Aqueous Polysulfide-Based Redox Flow Battery with Soluble Molecular Catalysts

Boosting the Rate Performance of Li-S Batteries Via Highly Dispersed Cobalt Nanoparticles Embedded into Nitrogen-Doped Hierarchical Porous Carbon

Electrocatalysis of polysulfide conversion by conductive RuO2 nano dots for lithium-sulfur batteries

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Sodium Polysulfides As Catholytes for Redox Flow Batteries

Bifunctional Catalyst for Liquid–Solid Redox Conversion in Room‐Temperature Sodium–Sulfur Batteries

Integrating CoP/Co heterojunction into nitrogen-doped carbon polyhedrons as electrocatalysts to promote polysulfides conversion in lithium-sulfur batteries

Synergistic Effect of In 2 O 3 /NC-Co 3 O 4 Interface on Enhancing the Redox Conversion of Polysulfides for High-Performance Li-S Cathode Materials at Low Temperatures

Architecting Freestanding Sulfur Cathodes for Superior Room‐Temperature Na–S Batteries