Abstract:Organic photovoltaics (OPVs) have been considered as one of the preliminary candidates for the third-generation solar cells due to their particularly advantages, such as light-weight, low cost, solution processability and mechanical flexibility. In recent years, the power conversion efficiency (PCE) of OPVs has achieved remarkable progress with the development of non-fullerene acceptors (NFAs), which exhibit stronger capability of light absorption and stability than the fullerene acceptors. However, the narrow absorption properties of organic materials still restrict the further breakthrough of the performance of OPVs. It is difficult for the binary heterojunction films to realize the effective wide spectrum utilization of solar energy. Ternary strategy, which consists of one donor and two acceptors or two donors and one acceptor in a bulk-heterojunction, has proven to be an effective and facile way to enhance performances of OPVs. The emergence of new NFAs such as ITIC, IT-4F, Y6 etc. greatly increases the selectivity of acceptors in a ternary system. It is necessary to investigate the compatibility of latest NFA materials and corresponding ternary device performance. In this article, we report a new ternary OPV system with dual NFAs and a polymer donor. The excellent NFA material (Y6), which was first reported in 2019, is used as the third component. Different concentrations of Y6 are introduced into the binary system based on PBDB-T-2F:IT-4F. The compatibility between materials and device performances are investigated through absorption capability of blend films, AFM, water contact angle, GISAXS, and corresponding electrical properties of devices. The 12.48% PCE is achieved from ternary OPVs with PBDB-T:IT-4F as the active layers containing 20wt% Y6 in acceptors, resulting from the enhanced Jsc of 22.09 mA/cm2, Voc of 0.83 V and FF of 68.45%. The origin of the improvement of the ternary OPVs is summarized below. Firstly, an apparently complementary absorption spectrum is obtained through the introduction of Y6, which has a stronger photo harvesting capability in the spectral range from 750 to 950 nm than IT-4F, and higher short current density (Jsc) is observed in the ternary devices than in the binary device. Secondly, a rougher surface of the active layer is observed by increasing the Y6 concentration, which may result in an inferior exciton dissociation and charge transport process, the existence of larger-scaled crystal is proved by the GISAXS technology. Thirdly, the introduced Y6 can help to suppress the bimolecular recombination, which is in favor of the incremental device performance. Approximately 17.85% PCE improvement is obtained in comparison with PBDB-T-2F:IT-4F based binary OPVs.

Over 17% Efficiency of Ternary Organic Photovoltaics Employing Two Acceptors with an Acceptor–Donor–Acceptor Configuration

Two Well-Compatible Acceptors with Efficient Energy Transfer Enable Ternary Organic Photovoltaics Exhibiting a 13.36% Efficiency

Ternary‐organic Photovoltaics with J71 As Donor and Two Compatible Nonfullerene Acceptors

Ternary Organic Photovoltaic Cells Exhibiting 17.59% Efficiency with Two Compatible Y6 Derivations as Acceptor

Approaching 18% efficiency of ternary organic photovoltaics with wide bandgap polymer donor and well compatible Y6 : Y6-1O as acceptor

Ternary Organic Solar Cells with Efficiency >16.5% Based on Two Compatible Nonfullerene Acceptors.

Over 17.6% Efficiency Organic Photovoltaic Devices with Two Compatible Polymer Donors

Exploring ternary organic photovoltaics for the reduced nonradiative recombination and improved efficiency over 17.23% with a simple large-bandgap small molecular third component

Dual Non-Fullerene Acceptors Based High Efficiency Ternary Organic Solar Cells

18.7% Efficiency Ternary Organic Solar Cells Using Two Non-Fullerene Acceptors with Excellent Compatibility

Achieving and Understanding of Highly Efficient Ternary Organic Photovoltaics: from Morphology and Energy Loss to Working Mechanism

Unique Energy Alignments of a Ternary Material System toward High‐Performance Organic Photovoltaics

The Multi-Functional Third Acceptor Realizes the Synergistic Improvement in Photovoltaic Parameters and the High-Ratio Tolerance of Ternary Organic Photovoltaics

Over 16.5% efficiency in ternary organic solar cells by adding an alloyed acceptor with energy transfer process

Realizing Stable High‐Performance and Low‐Energy‐Loss Ternary Photovoltaics through Judicious Selection of the Third Component

Multiple Roles of a Non-fullerene Acceptor Contribute Synergistically for High-Efficiency Ternary Organic Photovoltaics

Ternary Organic Blend Approaches for High Photovoltaic Performance in Versatile Applications

Enhanced Efficiency and Excellent Thermostability in Organic Photovoltaics via Ternary Strategy with Twisted Conjugated Compound

High-Performance Ternary Organic Solar Cells Enabled by Introducing a New A-DAD-A Guest Acceptor with Higher-Lying LUMO Level

Ternary Strategy Enabling High‐Performance Organic Solar Cells with Optimized Film Morphology and Reduced Nonradiative Energy Loss

Over 19 % Efficiency Ternary Organic Solar Cells Enabled by Tuning Charge Behaviors Through Quinoxalineimide-based Y-type Acceptors