Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Wettability Between 304 Stainless Steel and Refractory Materials

Temperature dependence of contact angles of water on a stainless steel surface at elevated temperatures and pressures: In situ characterization and thermodynamic analysis.

Wettability of Mold Flux with Various Droplet Size on Stainless Steel Substrate

Influence of Interface Electric Field on Interaction Between Molten Iron and Refractory Interface

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

Temperature Dependence of the Dynamic Contact Angles of Water on a Smooth Stainless-Steel Surface under Elevated Pressures

Measuring Dynamic Nonreactive Wetting Behavior Between Interstitial-Free Molten Steel and Alumina

Wetting and Spreading Behavior of Molten Iron in Contact with Graphite Substrate: Interfacial Effects

Interface Evolution Behaviors and Shear Strength of Vacuum Diffusion Bonded 45 Steel/additive Manufactured 316L Stainless Steel Joints

Effects of Different Oxidation Methods on the Wetting and Diffusion Characteristics of a High-Alumina Glass Sealant on 304 Stainless Steel

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Effect of slag basicity on the interfacial wetting behavior between CA6 refractories and CaO–SiO2–MgO–Al2O3 based slag

Interface Behaviors and Mechanical Properties of Diffusion Bonded 45 Steel/additive Manufactured 316L Steel Joints

Dynamic interaction of refractory and molten steel: Corrosion mechanism of alumina-magnesia castables

Influence of Interface Electric Field on Wettability Between Molten Iron and Submerged Entry Nozzle Interface

Enhancing the wettability for 4043 aluminum alloy on 301L stainless steel via chemical-etched surface texturing

The thermal contact resistance of a steel-ceramic interface with oxide intermediates

Reaction mechanism between Al2O3–MgO refractory materials and rare earth high-carbon heavy rail steel

Wettability and Interfacial Reaction between the K492M Alloy and an Al2O3 Shell

Study on reaction interface of carbon‐free oxide‐based refractories with lanthanum oxide and lanthanum aluminate

Research on the Wetting and Corrosion Behavior Between Converter Slag with Different Alkalinity and MgO-C Refractories