Abstract:To improve the mechanical properties of anion exchange membranes (AEMs) with bulky imidazolium cations, a series of anion-conductive poly(2,6-dimethyl-phenylene oxide)s (PPO)s with crosslinkable terminal double bonds were synthesized by the Menshutkin reaction. Following crosslinking via olefin metathesis at room temperature catalyzed by a Grubb's second generation catalyst, tough, transparent, and flexible PPO-based AEMs were obtained. The crosslinked AEMs exhibited good mechanical properties (tensile strength at maximum load of 20.8-49.9 MPa and values of elongation at break of 1.5-3.0%) though their bulky imidazolium cation groups which could destroy the film-forming ability of polymer. And the obtained mechanical properties were considerably better than those of the non-crosslinked AEMs with a similar architecture, which broke into small pieces during the process of membrane fabrication using solvent casting. Furthermore, the crosslinked AEMs exhibited an extremely low water uptake (up to 13.9 wt% at 80 degrees C) and minimal swelling (<7% at 80 degrees C), attributed to the high-density crosslinking network. A high bromide conductivity (22.9 mS/cm at 80 degrees C) was achieved despite the low water uptake for the crosslinked AEM. Moreover, long-term alkaline stability testing in 1 M NaOH at 80 degrees C, no obvious degradation of the imidazolium ring was observed, with the conductivity of aged crosslinked membranes remaining at similar to 100% after 960 h. It was assumed that the bulky substituents at the C2, C4, and C5 positions of imidazolium cations and the crosslinked architecture prevented H2O and/or OH- from attacking the cationic center. Moreover, the AEM fuel cell performance and durability was further explored for the membrane electrode assembly (MEA) with crosslinked and uncrosslinked bulky imidazolium-based ionomers in catalyst layers. An optimistic cell performance (a peak power density of 173 mW/cm(2) at 410 mA/cm(2)) and improved short-term durability at a constant current density of 200 mA/cm(2) were obtained for the crosslinked ionomers, and its lifetime was ca. 3 times longer than that of benzyltrimethylammonium functionalized PPO ionomer.

Bis-imidazolium Functionalized Self-Crosslinking Block Polynorbornene Anion Exchange Membrane

Poly(olefin)-Based Anion Exchange Membranes Prepared Using Ziegler–Natta Polymerization

Novel Cross-Linked Anion Exchange Membranes with Diamines As Ionic Exchange Functional Groups and Crosslinking Groups

Synthesis of Halogenated Benzonorbornadiene Monomer and Preparation of Self-Crosslinking Bisimidazole Cationic Functionalized Benzonorbornadiene Triblock Copolymer Anion Exchange Membrane

Towards high conductivity and stability diblock poly(norbornene)s-based anion exchange membranes crosslinked with alkyl quaternary ammonium cationic clusters

Novel Self-Cross-linked Multi-Imidazolium Cations Long Flexible Side Chains Triblock Copolymer Anion Exchange Membrane Based on ROMP-type Polybenzonorbornadiene

Interpenetrating Anion Exchange Membranes Using Poly(1-Vinylimidazole) As Bifunctional Crosslinker for Fuel Cells

Bis-imidazolium-based Anion-Exchange Membranes for Alkaline Fuel Cells

Highly Conductive and Robustly Stable Anion Exchange Membranes with a Star-Branched Crosslinking Structure

Physically and Chemically Stable Anion Exchange Membranes with Hydrogen-Bond Induced Ion Conducting Channels

Preparation and performance of crosslinked poly(arylene ether)s-based anion exchange membranes

Triblock Copolymer Anion Exchange Membranes Bearing Alkyl-Tethered Cycloaliphatic Quaternary Ammonium-Head-Groups for Fuel Cells

Olefin Metathesis-Crosslinked, Bulky Imidazolium-Based Anion Exchange Membranes with Excellent Base Stability and Mechanical Properties

Imidazolium-functionalized Anion Exchange Membranes Using Poly(ether Sulfone)s As Macrocrosslinkers for Fuel Cells

Anion Exchange Membranes Based on Sulfonated Poly(ether ether ketone) Crosslinked Methylpyrrolidinium Functionalized Poly (vinyl benzyl chloride) with High Chemical Stability

Crosslinked anion exchange membranes prepared from highly reactive polyethylene and polypropylene intermediates

Dimensionally and oxidatively stable anion exchange membranes based on bication cross-linked poly(meta-terphenylene alkylene)s

Highly Conductive and Dimensionally Stable Anion Exchange Membranes Based on Poly(dimethoxybenzene-co-methyl 4-Formylbenzoate) Ionomers

Synthesis and characterization of ion exchange capacity controlled and self-crosslinked anion exchange membranes

Multi-imidazolium Cationic Clusters Cross-Linked Hydrogenated Benzonorbornadiene Diblock Copolymer Anion Exchange Membranes for Improving Conductivity and Mitigating Swelling

A Mechanically Robust Anion Exchange Membrane with High Hydroxide Conductivity