Abstract:This work mainly studied the influence of the microstructure and crystallographic texture on the mechanical properties of the as-extruded Mg–Zn–Y–Zr alloys with different Y contents. The samples were machined from thick plates obtained by extrusion and the tensile tests were performed parallel to extrusion and transverse directions, respectively. Microstructure observation firmly indicated that the grain-refining effect of icosahedral quasicrystal phase (I-phase) was superior to that of the cubic W-phase. In addition, the tensile results indicated that I-phase could effectively improve the strength (yield strength and ultimate tensile strength) of alloys. However, strengthening effect of W-phase was lower. With the quantity of W-phase increasing, the strength of alloys was degraded. It also showed that the alloys were mechanically anisotropic, i.e. the longitudinal strength was higher than that of the transverse direction. However, the ductility of the transverse direction was superior. With the increase of Mg–Zn–Y phases, the anisotropy of the ultimate tensile strength (UTS) between the longitudinal and transverse directions increased remarkably. SEM fracture observations showed that the fractures of the TD samples were characterized by the typical “woody fracture”, with a large amount of cracked Mg–Zn–Y particles (I-phase and W-phase) distributed at the bottom of dimples. With Y content increasing, the average spacing of the zonal distributed Mg–Zn–Y particles on the fracture surface became narrow, which influenced the transverse mechanical properties greatly.

Mechanical Properties and Yield Asymmetry of Mg-Y-Zn Alloys: Competitive Behavior of Second Phases

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructures and Mechanical Properties of Mg-2Y-xZn (x=1, 2, 3 At%) Alloys

Effect of W-phase on the Mechanical Properties of As-Cast Mg–Zn–Y–Zr Alloys

Influence Of Y/Zn Mole Ratio On Phase Compositions And Mechanical Properties Of Mg-Y-Zn Alloys

Strengthening mechanisms in magnesium alloys containing ternary I, W and LPSO phases

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Microstructure, generation of intermetallic compounds and mechanical strengthening mechanism of as-cast Mg–4Y–xZn alloys

High Strength Mg-Zn-Y Alloys Reinforced Synergistically by Mg12ZnY Phase and Mg3Zn3Y2 Particle

Influence of Y/Zn Mole Ratio on the Phase Compositionand Mechanical Properties of Mg‐Y‐Zn Alloys

The Influence of Element Y on the Mechanical Properties of the As-Extruded Mg–Zn–Y–Zr Alloys

Effect of Zn/(Gd+Y) ratio on the microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Influence of Y on the Phase Composition and Mechanical Properties of As-Extruded Mg–Zn–Y–Zr Magnesium Alloys

Microstructures and Mechanical Properties of Mg–10Gd–6Y–2Zn–0.6Zr(wt.%) Alloy

Effect of Y Addition on the Microstructure and Mechanical Properties of Mg-6 Zn-1 Mn Magnesium Alloy

Influence of Higher Zn/Y Ratio on the Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

Effect of Microstructure and Texture on the Mechanical Properties of the As-Extruded Mg–Zn–Y–Zr Alloys

Effect of Y Concentration on the Microstructure and Mechanical Properties of As-Cast Mg–Zn–Y–Zr Alloys

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

Microstructure and mechanical properties of as-cast Mg−8Li−xZn−yGd (x=1, 2, 3, 4; y=1, 2) alloys