Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Mechanical, electronic and thermodynamic properties of TE-C36 under high pressure

First-Principles Study of High-Pressure Behavior of Solid β-HMX

The high-pressure phase transitions and vibrational properties of zinc-blende XTe (X = Zn, Cd, Hg): Performance of local-density-approximation density functional theory

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Structural, Mechanical, Thermal and Electronic Properties of Novel Ternary Carbide Al4si2c5 under High Pressure by Dft Calculation

First-Principle Calculations of Elastic, Electronic and Thermodynamic Properties of Tic under High Pressure

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

Theoretical Study of Structural, Mechanical, Thermal and Electronic Properties of Ti3B4 with Ta3B4 Structure under High Pressure

First-principles calculations to investigate thermodynamic, mechanical and electronic properties of Penta-C72 carbon under pressure effect

Structural and electrical properties of Ga–Te systems under high pressure

First-principles Calculations of Mechanical and Thermodynamic Properties of Tetragonal Be12Ti

Thermoelectric Properties of Ce3Te4 under High Pressure: First-Principles Calculation

Theoretical Investigations on Elastic and Thermodynamic Properties of CdTe

First-principles Calculations of Structural Phase Transition and Elastic Properties of BeTe under High Pressure

Elastic and Thermodynamic Properties of Zinc-Blende Znte under High Temperature and Pressure

Ab initio calculation of elastic and thermodynamic properties of W under high pressure

Study of structural stabilities and optical properties of HgTe under high pressure

First-Principles Calculations: Structural, Anisotropic, and Electronic Properties of BC14 Carbon Under Pressure

Ab initio study of structural, electronic and thermodynamic properties of Be<sub>12</sub>V under high temperature

Theoretical prediction of structural, elastic and thermodynamic properties of transition metal monosilicides CrSi, TiSi and ZrSi under high pressure

First-principles Study of Elastic, Electronic, and Optical Properties of Α-Teo2 under Pressure