Abstract:In order to implement numerical simulation of the thermal-mechanical behaviors in the nuclear fuel rods, a three-dimensional finite element model is established. The thermal-mechanical behaviors at the initial stage of burnup in both the pellet and the cladding are obtained. Comparison of the obtained numerical results with those from experiments validates the developed finite element model. The effects of the constraint conditions, several operation and structural parameters on the thermal-mechanical performances of the fuel rod are investigated. The research results indicate that: (1) with increasing the heat generation rates from 0.15 to 0.6 W/mm(3), the maximum temperature within the pellet increases by 99.3% and the maximum radial displacement at the outer surface of the pellet increases by 94.3%. And the maximum Mises stresses in the cladding all increase; while the maximum values of the first principal stresses within the pellet decrease as a whole; (2) with increasing the heat transfer coefficients between the cladding and the coolant, the internal temperatures reduce and the temperature gradient remains similar; when the heat transfer coefficient is lower than a critical value, the temperature change is sensitive to the heat transfer coefficient. The maximum temperature increases only 7.13% when h changes from 0.5 W/mm(2) K to 0.01 W/mm(2) K, while increases up to 54.7% when h decreases from 0.01 W/mm(2) K to 0.005 W/mm(2) K; (3) the initial gap sizes between the pellet and the cladding significantly affect the thermal-mechanical behaviors in the fuel rod; when the gap size varies from 0.03 mm to 0.1 mm, the highest temperature in the pellet increases by 19.7%, and the maximum first principal stress at the outer pellet surface decreases by 17.4%; it is critical to optimize the gap size in order to reduce the pellet-cladding mechanical interaction and avoid their contact at early stage. This study lays a foundation for the further research on the irradiation-induced mechanical behaviors in the fuel rods. (C) 2011 Elsevier Ltd. All rights reserved.

Research on Performance Enhancement of Nuclear Fuel with SiC Cladding by Using High Thermal Conductivity Fuels

Fuel Performance Optimization of U3Si2-SiC Design During Normal, Power Ramp and RIA Conditions

An Evaluation on In-Pile Behaviors of SiCf/SiC Cladding under Normal and Accident Conditions with Updated FROBA-ATF Code

Preliminary Neutronic/thermal-Hydraulic Evaluation and Safety System Optimization of PWR Loaded with Fully Ceramic Microencapsulated Fuel

A review on thermohydraulic and mechanical-physical properties of SiC, FeCrAl and Ti<sub>3</sub>SiC<sub>2</sub> for ATF cladding

A Comparative Study on Preliminary Performance Evaluation of ATFs under Normal and Accident Conditions with FRAP-ATF Code

Probabilistic View of SiC/SiC Composite Cladding Failure Based on Full Core Thermo-Mechanical Response

Steady-State Performance Analysis of a Dual-Cladding Design for Accident Tolerance Fuel

Three-dimensional FE analysis of the thermal-mechanical behaviors in the nuclear fuel rods

Neutronic Analysis on Potential Accident Tolerant Fuel-Cladding Combination U$_3$Si$_2$-FeCrAl

Fuel performance of chromium-coated zirconium alloy and silicon carbide accident tolerant fuel claddings

Finite element based fuel performance investigation of U3Si2-FeCrAl design under normal and RIA conditions

AP-1000 fuel assembly performance with UO2 and UO2/U3Si2 fuels and silicon carbide cladding from the viewpoint of neutronics

Transient Fuel Performance Analysis of UO2–BeO Fuel with Composite SiC Coated with Cr Cladding Based on Multiphysics Method

Simulation on Pellet–Cladding Mechanical Interaction of Accident Tolerant Fuel with Coated Cladding

A Comparative Study of In-Pile Behaviors of FeCrAl Cladding under Normal and Accident Conditions with Updated FROBA-ATF Code

Numerical Simulation Research on the Irradiation-Thermal-Mechanical Performance Evolution of FCM Fuel

Neutronic Design and Evaluation of a PWR Fuel Assembly with Accident Tolerant-Fully Ceramic Micro-Encapsulated (AT-FCM) Fuel

Preliminary Evaluation of U3Si2-FeCrAl Fuel Performance in Light Water Reactors Through a Multi-Physics Coupled Way

DEVELOPMENT OF AN ANISOTROPIC MECHANICAL MODEL FOR FROBA CODE AND ITS APPLICATIONS FOR SIC COMPOSITE CLADDING ANALYSIS

Influence of Accident-Tolerant Fuel With Steel Cladding for Sustainable Heat Transfer in the Reactor Core of VVER-1200