Abstract:The influence of blades assembly, i.e., the blade number on the solidification process, heat exchange and grain structure on a directionally solidified Ni-based superalloy DZ125 was investigated by combining the experimental and simulation results. The casting process was simulated thermodynamically by ProCAST software, where the interface heat transfer coefficient was precisely determined by a measurement with thermocouples. There is a good agreement between experimental and simulation results. It was interestingly found that with the number of blades increasing from 6 to 10, due to the decrease in radiation absorption efficiency, the maximum temperature and the heating rate decrease in the mold, during the preheat process. During the withdrawal procedure, increased assembly numbers reduce the radiation exchange from mold to the enclosure, resulting in the decrease in cooling rate and temperature gradient of the blades. At the end of withdrawal, the slower cooling rate of the outside balances the temperature distribution of internal and external surfaces on the rabbet of blade. Graphic abstract The interface heat transfer coefficient (IHTC) values of DZ125 casting system were investigated by inverse method. Then, a series of assembly blade groups were designed and being cast and calculated. Values of IHTC are proved to be suitable for different assembly groups of casting in this case. Based on simulation and experimental results, it was interestingly found that: In the preheating process, with the number of blades increased, the maximum temperature on the mold becomes lower and the heating rate becomes slower, which result from the decrease in radiation efficiency between the mold and graphite heater. During the withdrawal, increasing assembly blade number reduced the radiation exchange from the mold to the enclosure, and it results in the cooling rate and temperature gradient on the blades getting decreased. At the end of withdrawal, the slower cooling rate leads to the temperature distribution maintaining uniformity for internal and external surfaces on the rabbet of the blade.

Directional Solidification Behavior of Turbine Blades in DZ125 Alloy:Design of Blade Numbers on Assembly

Dependence of Microstructural Evolution on the Geometric Structure for Serviced DZ125 Turbine Blades

Microstructural Evolution of Directionally Solidified DZ125 Superalloy Castings with Different Solidification Methods

Effect of Directional Solidification Methods on the Cast Microstructure and Grain Orientation of Blade Shaped Dz125 Superalloy

Study on the Temperature Field and Grain Structure of Large-Scale DZ466 Ni-Based Superalloy During Directional Solidification Process

Multiscale Modeling and Simulation of Directional Solidification Process of Ni-Based Superalloy Turbine Blade Casting

Study on Mechanical Properties of DZ125 Directional Solidification Turbine Blades in Different Positions

Numerical Simulation of Unidirectional Solidification Process of Turbine Blade Castings

Numerical Simulation of Grain Growth of Directionally Solidified DZ4125 Alloy under Varied Blade Orientations

Temperature Field and Microstructure Simulation of Directional Solidification Process of Single Crystal Blade Prepared Efficiently with Different Module Structures

NUMERICAL SIMULATION OF DIRECTIONAL SOLIDIFICATION PROCESS OF MULTIPLE TURBINE BLADES OF Ni-BASED SUPERALLOY

Influence of withdrawal rate on microstructures of blade shaped directionally solidified DZ125 superalloy

Development of Numerical Simulation in Nickel-Based Superalloy Turbine Blade Directional Solidification

Multiscale Modeling and Simulation of Directional Solidification Process of Turbine Blade Casting with MCA Method

Numerical Simulation of Directional Solidification of Single Crystal Turbine Blade Casting

A Design of Non-Uniform Thickness Mould for Controlling Temperature Gradient and S/L Interface Shape in Directionally Solidified Superalloy Blade

Progress on Modeling and Simulation of Directional Solidification of Superalloy Turbine Blade Casting

Evaluation Of Temperature And Stress In First Stage High Pressure Turbine Blades Of A Directionally-Solidified Superalloy Dz125 After Service In Aeroengines

Simulation and Experimental Investigation of Grain Structure, Residual Stress,γ′ Phases in Single Crystal Blade

Vibration Fatigue Assessment and Crack Propagation Mechanism of Directionally Solidified Superalloy with Film Cooling Holes

Numerical Simulation of Solidification Process on Single Crystal Ni-Based Superalloy Investment Castings