Abstract:Magnesium alloys WE43 and AZ91D offer weight savings for structural applications. WE43 contains rare-earth elements such as yttrium and neodymium, whereas AZ91D and the AZ class of alloys are lower-cost containing aluminium and zinc. This work uses a modified version of the latter, identified as AZ91D*, where calcium and yttrium have been added. Laser Engineered Net Shaping (LENS) equipment was used to investigate the 3D printing behaviour of gas-atomized WE43 and AZ91D* material. Process evaluations were first done using single track laser scans across wrought substrates of WE43 and AZ31. Process parameters were then developed that enabled deposition of build coupons with less than 1% porosity. These were used for microstructural and mechanical property assessments. The energy densities used were in the range of 40 – 60 J/mm2 for AZ91D*, while for WE43 a value of 50 J/mm2 was selected. A focus of the work was managing the tendency of magnesium materials to fume heavily during deposition, while achieving a deposit with close to nominal density, i.e. having a low incidence of voids or other micro- or macro-structural defects. The porosity of AZ91D* builds did not seem to correlate with increasing deposition energy density, however WE43 builds did, up to a practical limit imposed by generation of excessive fume. WE43 generated much less fume than AZ91D*. Analysis of the input powder materials indicate the presence of oxides on the particle surfaces. The WE43 powders had a noticeable shell of yttrium oxide. The microstructures of WE43 builds show the presence of arc-shaped structures that are likely the same yttrium oxides, partially, or fully 'unfolded'. Tensile testing was conducted on WE43 build coupons to assess the effect of a T6 heat treatment. The effect on the ultimate tensile and yield strengths was negligible, however the % elongation at break almost doubled. Inspection of the fracture surfaces suggests this was due to a change in mechanism from fracture initiation at sites of lack-of-fusion/un-melted particles, to a more ductile micro-void coalescence. Furthermore, a not previously described microstructure anomaly was observed: the presence of pure elemental magnesium crystallites and films on the fracture surface. These are attributed to condensation of magnesium vapour on previously built layers and are a possible reason for the existence of lack-of-fusion defects. The in-depth study of process fundamentals will enable future work on process fume inhibition based on process optimization and alloy composition with the goal of producing parts for biomedical and lightweighting applications.

Preparation of Laminated Structure in AZ31 Magnesium Alloy by Explosive Welding

Explosive Welding of Thin Aluminum Plate onto Magnesium Alloy Plate Using a Gelatin Layer as a Pressure-Transmitting Medium

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

On the heterogeneous microstructure and strengthening mechanisms in a laser welding AZ80 magnesium alloy

Study of microstructure evolution in the aluminum‒magnesium alloy AlMg6 after explosive welding and heat treatment

Analysis of Microstructure and Mechanical Properties of AZ31B Thick Plate Magnesium Alloy Stir Friction Welded Joints

Microstructures and Mechanical Properties of Resistance Spot Welded Magnesium Alloy Joints

Effect of Ultrasonic Vibration Assistance on Microstructure Evolution and Mechanical Properties in Laser-Welded AZ31B Magnesium Alloy

Study on the Microstructure and Mechanical Properties of a Ti/Mg Alloy Clad Plate Produced by Explosive Welding

Analysis of Microstructure and Mechanical Properties of AZ31B Magnesium Alloy/AA6061 Aluminum Alloy Welded Joint by Ultrasonic Welding

Microstructure homogeneity and mechanical properties of laser-arc hybrid welded AZ31B magnesium alloy

The Influence of Heat and Cryogenic Treatment on Microstructure Evolution and Mechanical Properties of Laser-Welded AZ31B

Effect of pulse overlap rate on the microstructure and mechanical properties of laser welds of thin AZ31 magnesium alloy

Microstructure and Properties of Magnesium Alloy Joints Bonded by using Gallium with the Assistance of Ultrasound at Room Temperature

Additive manufacturing of WE43 and modified AZ91D magnesium alloys using the laser engineered net shaping process

Effect of preheating temperature on the microscopic structure and mechanical performance of pulsed laser welding in sheet AZ31 alloy

Ultrasonic Welding of AZ31B Magnesium Alloy and Pure Copper: Microstructure, Mechanical Properties and Finite Element Analysis

Microstructure and Properties of Mg-Gd-Y-Zn-Mn High-Strength Alloy Welded by Friction Stir Welding

Characteristics of Microstructure and Microhardness of Friction Stir Welded Joints for AZ31 Magnesium Alloy

Research for microstructure and mechanical properties of AZ91 magnesium alloy welded joint with magnetic field and activated flux

The Effect of Annealing on the Properties of AW5754 Aluminum Alloy-AZ31B Magnesium Alloy Explosively Welded Bimetals