Abstract:Square-small holes are used as a critical feature in the fields of aerospace, machine-tooling, automation, and mechanical component construction. Electrochemical drilling (EC-drilling) is a promising approach for manufacturing square-small holes. However, the distribution of flow field in the inter-electrode gap (IEG) becomes non-uniform because of the unique structure of the square-cross-section tubular tool, leading to the accumulation of electrolytic by-products in the IEG. Consequently, both shape accuracy and machining efficiency are reduced. This paper proposes an EC-drilling process with workpiece vibration, in which low-frequency vibration is applied to the workpiece and the size of the frontal IEG is periodically altered. This approach can improve the flow field distribution and eliminate constant low flow velocity zones, resulting in enhanced mass transfer in the IEG. A 3D computational fluid dynamics (CFD) model includes discrete phase was developed to analyze the characteristics of the flow field and elucidate the enhancement mechanism of workpiece vibration in the transfer process. Simulation results revealed that a pulsating electrolyte flow field was produced in both frontal and side IEG induced by workpiece vibration, and that high flow velocity zones were generated alternately in frontal IEG and side IEG. With minimum frontal IEG, there was a high flow velocity in frontal IEG, with parcels (each parcel contains 205 particles) being transported smoothly from frontal IEG to the side IEG. High flow velocity switched to the side IEG when frontal IEG was maximum, and parcels that accumulated in the side IEG were easily removed. With the workpiece vibration process repeated, the parcel transfer process in the IEG was enhanced and the number of parcels accumulating in the IEG significantly reduced. The enhancement of workpiece vibration on the machining of square-small hole was verified by experiments, reflected as enhancement in both the surface quality and shape accuracy of square-small holes. Increasing both the vibration amplitude and frequency enhanced the removal rate of electrolytic by-products, thereby improving machining quality. Machining quality was further improved using a high pulse frequency and low pulse duty cycle. With appropriate parameters, the maximum cathode feed rate reached 1.44 mm/min, 2.4 times that previously reported, and the width and corner radius of the square-small hole was 1.16 mm ± 0.003 mm and 149 μm, respectively, with a surface roughness of 0.54 μm on the sidewall of the square-small hole.

A Novel Micro-Edm Method to Improve Microhole Machining Performances Using Ultrasonic Circular Vibration (UCV) Electrode

A novel EDM method using longitudinal-torsional ultrasonic vibration (LTV) electrodes to improve machining performance for micro-holes

Improvement of ultrasonic cavitation and pumping effect in microhole EDM

A novel ultrasonic vibration-assisted micro-EDM method to improve debris removal performance using relative three-dimensional ultrasonic vibration (RTDUV)

The effect of ultrasonic amplitude on the performance of ultrasonic vibration-assisted EDM micro-hole machining

Experimental research and multi-objective optimization of ultrasonic vibration–assisted EDM for Ti6Al4V micro-holes

Theoretical and experimental study on micro ultrasonic-assisted electrochemical drilling with high speed electrode

Machining performance enhancement of deep micro drilling using electrochemical discharge machining under magnetohydrodynamic effect

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

Vibration-Assisted Servo Scanning 3d Micro Edm

Study on Micro-hole Electrochemical Machining Process with Sidewall-insulated Tool Electrode

Experimental Research of High-Quality Drilling Based on Ultrasonic Vibration-Assisted Machining

Design of a Micro-hole EDM Tool and its Machining Experiments

Enhancement mechanism of electrochemical drilling square-small holes with workpiece vibration

An Investigation into Accumulative Difference Mechanism in Time and Space for Material Removal in Micro-EDM Milling

Interelectrode gas–liquid-solid three-phase flow analysis and simulation for drilling holes with high aspect ratio by micro-EDM

Experimental research on vibration assisted EDM of micro-structures with non-circular cross-section

Vibration-assisted Feeding Mechanism of Micro Electrode for Micro Hole EDM and Its Machining Experiments

Effect of ultrasonic assisted EDM based on horizontal vibration on deep and small hole machining

Precision EDM of Micron-Scale Diameter Hole Array Using in-Process Wire Electro-Discharge Grinding High-Aspect-Ratio Microelectrodes

A High Energy Density Pulsed Power Supply for Micro EDM of High Aspect Ratio Holes