Optimal kinematic design of a three translational DoFs parallel manipulator

LiuXin-Jun

IF: 2.7

2006-01-01

Robotica

Abstract:In this paper, an optimal kinematic design method of a three translational DoFs parallel manipulator is presented. The design is based on the concept of performance chart, which can show the relati...

What problem does this paper attempt to address?

Optimal kinematic design of a three translational DoFs parallel manipulator

Xin-Jun Liu

DOI: https://doi.org/10.1017/S0263574705002079

IF: 2.7

2006-01-01

Robotica

Abstract:In this paper, an optimal kinematic design method of a three translational DoFs parallel manipulator is presented. The design is based on the concept of performance chart, which can show the relationship between a criterion and design parameters graphically and globally. The normalization on the design parameters of the studied manipulator makes it possible that the design space, which is made up of the normalized parameters, is limited. The design space includes of all possible basic similarity manipulators (BSMs). As any one of the BSMs represents all of its similarity manipulators (SMs) in terms of performances, if one BSM is optimal, its SMs are optimized as well. The said optimal BSM is from the optimum region, which is the intersecting result of involved performance charts. In this paper, the related performance criteria are good-conditioning workspace (GCW), global conditioning index (GCI) and global stiffness index (GSI). As an applying example, a design result of the parallel manipulator with a desired task workspace is presented. The results of the paper are very useful for the design and application of a parallel manipulator.
Kinematic Optimal Design of a Spatial 3-DOF Parallel Manipulator

Xin-Jun Liu,Jinsong Wang

DOI: https://doi.org/10.1007/978-3-642-36929-2_9

2013-01-01

Abstract:This chapter provides a case study for the kinematic optimal design of a spatial 3-DOF (two translations and one rotation) parallel manipulator. The final design of the manipulator is used for a module of a five-axis hybrid kinematic machine developed at Tsinghua University.
Optimal Kinematic Design of a 2-DOF Planar Parallel Manipulator

Wu Jun,Li Tiemin,Liu Xinjun,Wang Liping

DOI: https://doi.org/10.1016/s1007-0214(07)70040-8

2007-01-01

Abstract:Closed-form solutions were developed to optimize kinematics design of a 2-degree-of-freedom (2-DOF) planar parallel manipulator. The optimum design based on the workspace was presented. Meanwhile, a global, comprehensive conditioning index was introduced to evaluate the kinematic designs. The optimal parallel manipulator is incorporated into a 5-DOF hybrid machine tool which includes a 2-DOF rotational milling head and a long movement worktable. The results show that the planar parallel manipulator-based machine tool can be successfully used to machine blades and guide vanes for a hydraulic turbine.
A New Method for Optimum Design of Parallel Manipulator Based on Kinematics and Dynamics

Jun Wu,Liping Wang,Zheng You

DOI: https://doi.org/10.1007/s11071-010-9682-x

IF: 5.741

2010-01-01

Nonlinear Dynamics

Abstract:This paper presents a new method for the optimum design of parallel manipulators by taking both the kinematics and dynamic characteristics into account. The optimum design of a 3-DOF 4-RRR planar parallel manipulator with actuation redundancy is investigated to demonstrate the method. The kinematic performance indices such as the conditioning index, the velocity index, and workspace area are analyzed. Further, the dynamic dexterity, which is used to evaluate the dynamic characteristics, is investigated. The corresponding atlases are represented graphically in the established design space. Based on these atlases, the geometrical parameters without dimension are determined. Then the optimum dimensional parameters are achieved based on the optimum non-dimensional result. By using the method proposed in this paper, the designer can obtain the optimum result with respect to both kinematic performance indices and dynamic performance indices. Since the dynamic performance is considered in the process of optimum design by using the method proposed in this paper, it is expected to realize the high dynamics of parallel manipulators.
Optimal Kinematic Design and Application of a Redundantly Actuated 3DOF Planar Parallel Manipulator

Jun Wu,Jinsong Wang,Liping Wang

DOI: https://doi.org/10.1115/1.2890118

2008-01-01

Journal of Mechanical Design

Abstract:This paper addresses optimal kinematic design and application of a redundantly actuated parallel manipulator with 3DOFs. Based on the kinematic model, the Jacobian matrix is derived and then transferred to a uniform form such that the conditioning index has explicit physical meaning. Based on the task workspace, the width between two columns is determined Then, a comprehensive performance index, which compromises the conflict between workspace utilization performance measure and conditioning index, is proposed for the optimum design. The parallel manipulator is incorporated into a 4DOF hybrid machine tool, which also includes a feed worktable. Furthermore, a 5DOF machine tool is created by combining the parallel manipulator with a 2DOF worktable to machine blades of gas turbines.
Optimum Kinematic Design of the 4R 2-DOF Parallel Mechanism

Xie Fugui,Liu Xinjun,Wang Liping,Wang Jinsong

DOI: https://doi.org/10.1016/s1007-0214(09)70132-4

2009-01-01

Abstract:This paper analyzes the kinematic optimization design of the 4R 2-DOF parallel mechanism taking into account the force transmissibility. Three indices are introduced to reflect the force transmissibility. Based on these indices and their performance charts, the optimization design process with respect to the workspace is presented in detail. The results show that the designed mechanism is not only far from every singularity but also has good force transmissibility in its workspace. These kinematic optimization indices can be extended to other parallel mechanisms.
Optimization Design of a Novel 4-DOF Parallel Manipulator

Tianrui Xu,Jun Wu,Binbin Zhang

DOI: https://doi.org/10.1109/cyber46603.2019.9066638

2019-01-01

Abstract:This paper deals with optimization design of a novel 4-DOF parallel manipulator with 4 chains and 2 moving platforms. The linear motion between the moving platforms can be transformed into the rotary motion of the end effector. Based on the kinematic model, the dynamic model is derived by using the principle of virtual work. The workspace volume, error transfer characteristic, dexterity and stiffness evaluation indexes are investigated. Using univariate search technique, the multi-objective optimization is conducted and the optimal structure size ratio is solved.
Kinematic optimal design of a 2-degree-of-freedom 3-parallelogram planar parallel manipulator

xinjun liu,jie li,yanhua zhou

DOI: https://doi.org/10.1016/j.mechmachtheory.2014.12.014

IF: 4.93

2015-01-01

Mechanism and Machine Theory

Abstract:A 2-degree-of-freedom (2-DOF) 3-parallelogram planar parallel manipulator (PPM) can follow an arbitrary planar curve and keep the end-effector in a definite posture. Such features are valuable for spray-painting robots. Considering these advantages, authors proposed a new spray-painting robot containing a 2-DOF 3-parallelogram PPM. In order to obtain a spray-painting robot with the best performance, the 2-DOF 3-parallelogram PPM should possess the largest workspace and most stable transmissibility. This study addresses the performance evaluation and kinematic optimization of this manipulator. First, the kinematics of the manipulator is analyzed, and performance indices that consider desirable workspace and transmissibility are proposed. Then, the process to determine optimal geometry parameters by using performance atlases is presented. Finally, a 2-DOF 3-parallelogram PPM with desirable workspace and transmissibility is identified.
Determination of the Link Lengths for a Spatial 3-DOF Parallel Manipulator

Xin-Jun Liu,Jinsong Wang,Jongwon Kim

DOI: https://doi.org/10.1115/1.2159028

2006-01-01

Journal of Mechanical Design

Abstract:This paper addresses the issue of determining the optimal geometric parameters of a 3-DOF parallel manipulator One of the advantages of the manipulator is that the moving platform exhibits high tilting capabilities, e.g., as much as +/- 50 deg. The first step of the new optimal methodology proposed in this paper to achieve the optimum design involves developing a design space that includes all possible basic similarity manipulators. The next step deals with the graphical representation of atlases that can illustrate relationships between performance criteria and design parameters. With such atlases, the designer can identify an optimum region with respect to the specification on performances. The region contains the optimum candidates, from which we can select one directly. Finally, the geometric parameters of the manipulator can be reached by comparing the desired workspace and the good-conditioning workspace. The design methodology discussed in this paper has no process to establish the objective function and does not involve any optimization algorithm, which is normally used in traditional optimization. We expect that since each manipulator in the developed design space represents all of its similarity manipulators in terms of performances, this method will guarantee an optimum design result.
A Closed-Form Optimal Kinematic Design of the Prrrp Parallel Manipulator

Xin-Jun Liu,Jinsong Wang

DOI: https://doi.org/10.1115/1.2712224

2006-01-01

Journal of Mechanical Design

Abstract:This paper addresses the optimal kinematic design of the PRRRP parallel manipulator that is actuated horizontally by linear actuators. Kinematically, the symmetrical PRRRP parallel manipulator has only one geometric parameter, i.e., the link length of each of the two legs. Here, we propose a design approach utilizing the performance chart and local performance specification. The key problem in the design of the manipulator is the determination of not the link length but the workspace that the manipulator can reach satisfying the design specification. Such a kind of workspace when the link length is unit is defined as the basic good-conditioning workspace (GCW). For the manipulator studied here, the link length is actually the ratio of the desired task workspace to the basic GCW. This paper gives an effective method to obtain the basic GCW with respect to indices in closed form. One of the advantages of the method is that the basic GCW is achieved by taking into account both the global and local indices.
A new methodology for optimal kinematic design of parallel mechanisms

Xin-Jun Liu,Jinsong Wang

DOI: https://doi.org/10.1016/j.mechmachtheory.2006.08.002

IF: 4.93

2007-01-01

Mechanism and Machine Theory

Abstract:This paper addresses the general issue of optimal kinematic design of parallel mechanisms. Optimal design is one of the most challenging issues in the field. To solve the design problem ideally, the difficulties that one should solve can be summarized as: (a) reducing the number of design parameters; (b) specifying the bounds of each parameter reasonably; (c) defining a parameter design space, in which the optimal kinematic design can be implemented logically; (d) providing all possible optimal results. This paper proposes an optimal kinematic design methodology, which is referred to as Performance-Chart based Design Methodology (PCbDM), for parallel mechanisms with fewer than five linear parameters. Some steps in this methodology are also helpful for the objective-function based optimal design. The results of this paper will be very useful in developing the computer-aided design system for parallel mechanisms. The proposed design methodology can be also applied in serial and parallel robots or any other mechanisms.
Dynamic Manipulability and Optimization of a Redundant Three DOF Planar Parallel Manipulator

Hua Shao,Liping Wang,Liwen Guan,Jun Wu

2009-01-01

Abstract:This paper deals with the dynamic manipulability and dynamic optimization of a redundantly actuated three degree-of-freedom (DOF) parallel manipulator. The dynamic formulation is derived based on the virtual work principle. The reciprocal of the condition number of the inertia matrix is presented as an index to evaluate the dynamic manipulability of the manipulator. Furthermore, a global dynamic conditioning index, which considers the condition number of inertia matrix over the task workspace, is proposed. Then the global index is applied for optimizing the dynamic manipulability of the manipulator. Result of the optimization of the manipulators based on the global index is included.
Dynamic Manipulability and Optimization of A Two Dof Parallel Mechanism

Shao Hua,Wang Jinsong,Wang Liping,Guan Liwen

DOI: https://doi.org/10.3901/cjme.2010.04.403

IF: 2.964

2010-01-01

Chinese Journal of Mechanical Engineering

Abstract:The dynamic dexterity is an important issue for manipulator design, some indices were proposed for analyzing dynamic dexterity, but they can evaluate the dynamic performance just at one pose in the workspace of the manipulator, and can’t be applied to dynamic design expediently. Much work has been done in the kinematic optimization, but the work in the dynamic optimization is much less. A global dynamic condition number index is proposed and applied to the dynamic optimization design the parallel manipulator. This paper deals with the dynamic manipulability and dynamic optimization of a two degree-of-freedom （DOF） parallel manipulator. The particular velocity and particular angular velocity matrices of each moving part about the part’s pivot point are derived from the kinematic formulation of the manipulator, and the inertial force and inertial movement are obtained utilizing Newton-Euler formulation, then the inverse dynamic model of the parallel manipulator is proposed based on the virtual work principle. The general inertial ellipsoid and dynamic manipulability ellipsoid are applied to evaluate the dynamic performance of the manipulator, a global dynamic condition number index based on the condition number of general inertial matrix in the workspace is proposed, and then the link lengths of the manipulator is redesigned to optimize the dynamic manipulability by this index. The dynamic manipulability of the origin mechanism and the optimized mechanism are compared, the result shows that the optimized one is much better. The global dynamic condition number index has good effect in evaluating the dynamic dexterity of the whole workspace, and is efficient in the dynamic optimal design of the parallel manipulator.
Dimension optimization of a planar 3-RRR parallel manipulator considering motion and force transmissibility

Yuzhen Chen,Xinjun Liu,Xiang Chen

DOI: https://doi.org/10.1109/ICMA.2013.6617996

2013-01-01

Abstract:As the intrinsic characteristic of parallel manipulators, motion/force transmission performance has an extremely important influence on the performance of parallel robot systems. This study focuses on the evaluation of the motion/force transmission performance and dimensional optimization of a planar 3-RRR parallel manipulator by considering its motion/force transmissibility. An inverse kinematic analysis of the manipulator is presented. The local transmission index (LTI) of the manipulator is calculated, and two global design indices are defined based on the LTI for performance evaluation and dimensional synthesis. The process of optimal kinematic design of the manipulator based on performance charts is then presented. The optimized manipulator has a large workspace in area and shape, within which it has good motion/force transmissibility.
A three translational DoFs parallel cube-manipulator

LiuXin-Jun,JeongJay Il,KimJongwon

IF: 2.7

2003-01-01

Robotica

Abstract:This paper concerns the presentation and analysis of a type of three translational degrees of freedom (DoFs) parallel cube-manipulator. The parallel manipulators are the topology architectures of t...
Optimal Design of a New Spatial 3-DOF Parallel Robot with Respect to a Frame-Free Index

JinSong Wang,XinJun Liu,Chao Wu

DOI: https://doi.org/10.1007/s11431-008-0305-4

2009-01-01

Abstract:Optimal design is one of the most important issues in robots. Since the very beginning, the concepts of the Jacobian matrix, manipulability and condition number, which are used successfully in the field of serial robots, have been applied to parallel robots. Unlike serial robots, parallel robots are good for motion/force transmission. Their performance evaluation and design should be correspondingly different. This paper is an attempt to optimally design a novel spatial three-degree-of-freedom (3-DOF) parallel robot by using the concept of motion/force transmission. Accordingly, three indices are defined. The suggested indices are independent of any coordinate frame and could be applied to the analysis and design of a parallel robot whose singularities can be identified wholly by using the relative angle between the output and adjacent links, and by using the relative angle between the input and adjacent links.
Optimal Design of a Novel 4-Degree-of-freedom Parallel Mechanism with Flexible Orientation Capability

Weiyao Bi,Fugui Xie,Xin-Jun Liu,Xuan Luo

DOI: https://doi.org/10.1177/0954405417731469

2017-01-01

Abstract:This article proposes a novel spatial parallel kinematic mechanism with three kinematic limbs and 4 degrees of freedom. Its mobile platform can realize two translations and two rotation movements. Of note is that this mechanism can realize flexible A-/B-axis rotation (rotations about the x- and y-axes) and the transformation between vertical machining mode and horizontal machining mode. Using Tilt and Torsion angle description method, the kinematics analysis of this parallel kinematic mechanism is carried out. On this basis, the geometrical parameters, including parameters of three limbs and mobile platform, are optimized. In view of the particularity of configuration, the limb in the postposition with two active inputs is analyzed first and then the remaining two identical limbs. In the optimal design, motion/force transmissibility is taken into consideration, and the local transmission index is used as the performance evaluation criterion to investigate the orientation capability of this parallel kinematic mechanism. Using performance atlases method, the optimal kinematic design of the 4-degree-of-freedom parallel kinematic mechanism is carried out and a set of preferable optimized parameters is obtained at last. By virtue of the kinematic advantages, the proposed parallel kinematic mechanism can be used as the modular machining unit in five-axis machine centers. Based on this work, a machine tool with high flexibility has been developed to process the five faces of a workpiece within one setup.
Optimizing the kinematic chains for a spatial parallel manipulator via searching the desired dexterous workspace

Zhao Jing-Shan,Zhang Sheng-Lan,Dong Jing-Xin,Feng Zhi-Jing,Zhou Kai

DOI: https://doi.org/10.1016/j.rcim.2005.09.003

IF: 10.103

2007-01-01

Robotics and Computer-Integrated Manufacturing

Abstract:This paper exploits a new algorithm to optimize the length of the legs of a spatial parallel manipulator for the purpose of obtaining a desired dexterous workspace rather than the whole reachable workspace. With the analysis of the degree of freedom (DoF) of a manipulator, we can select the least number of variables to depict the kinematic constraints of each leg of a manipulator. The optimum parameters can be obtained by searching the extreme values of the objective functions with the given adroit workspace. Example is utilized to demonstrate the significant advantages of this method in the dexterous workspace synthesis. In applications, this method can be widely used to synthesize, optimize and create all kinds of new spatial parallel manipulator with a desired dexterous workspace.
Kinematics, dynamics and dimensional synthesis of a novel 2-DoF translational manipulator

Xin-Jun Liu,Qi-Ming Wang,Jinsong Wang

DOI: https://doi.org/10.1007/s10846-005-3507-z

2005-01-01

Abstract:In the past few years, parallel manipulators have become increasingly popular in industry, especially, in the field of machine tools. In this paper, a novel 2-degree-of-freedom (DoF) parallel manipulator, which has two translational DoFs, is proposed. It is characterized by the fact that the output of the manipulator is two planar DoFs of a rigid body, while its orientation remains constant. The inverse and forward kinematics can be described in closed form. The velocity equation, singularity, and workspace of the manipulator are presented. In addition the inverse dynamics problem of the device is investigated employing the Lagrange multipliers approach. The dimensional synthesis based on the workspace and conditioning indices is presented. The proposed manipulator can be applied to the field of machine tools or used as the mobile base for a spatial manipulator. The results of the paper are very useful for the design and application of the new manipulator.

Optimal kinematic design of a three translational DoFs parallel manipulator

Optimal kinematic design of a three translational DoFs parallel manipulator

Kinematic Optimal Design of a Spatial 3-DOF Parallel Manipulator

Optimal Kinematic Design of a 2-DOF Planar Parallel Manipulator

A New Method for Optimum Design of Parallel Manipulator Based on Kinematics and Dynamics

Optimal Kinematic Design and Application of a Redundantly Actuated 3DOF Planar Parallel Manipulator

Optimum Kinematic Design of the 4R 2-DOF Parallel Mechanism

Optimization Design of a Novel 4-DOF Parallel Manipulator

Kinematic optimal design of a 2-degree-of-freedom 3-parallelogram planar parallel manipulator

Determination of the Link Lengths for a Spatial 3-DOF Parallel Manipulator

A Closed-Form Optimal Kinematic Design of the Prrrp Parallel Manipulator

A new methodology for optimal kinematic design of parallel mechanisms

Dynamic Manipulability and Optimization of a Redundant Three DOF Planar Parallel Manipulator

Dynamic Manipulability and Optimization of A Two Dof Parallel Mechanism

Dimension optimization of a planar 3-RRR parallel manipulator considering motion and force transmissibility

A three translational DoFs parallel cube-manipulator

Optimal Design of a New Spatial 3-DOF Parallel Robot with Respect to a Frame-Free Index

Optimal Design of a Novel 4-Degree-of-freedom Parallel Mechanism with Flexible Orientation Capability

Optimizing the kinematic chains for a spatial parallel manipulator via searching the desired dexterous workspace

Kinematics, dynamics and dimensional synthesis of a novel 2-DoF translational manipulator