Abstract:Balancing interfacial stability and Li+ transfer kinetics through surface engineering is a key challenge in developing high-performance battery materials. Although conformal coating enabled by atomic layer deposition (ALD) has shown great promise in controlling impedance increase upon cycling by minimizing side reactions at the electrode–electrolyte interface, the coating layer itself usually exhibits poor Li+ conductivity and impedes surface charge transfer. In this work, we have shown that by carefully controlling postannealing temperature of an ultrathin ZrO2 film prepared by ALD, Zr4+ surface doping could be achieved for Ni-rich layered oxides to accelerate the charge transfer yet provide sufficient protection. Using single-crystal LiNi0.6Mn0.2Co0.2O2 as a model material, we have shown that surface Zr4+ doping combined with ZrO2 coating can enhance both the cycle performance and rate capability during high-voltage operation. Surface doping via controllable postannealing of ALD surface coating layer reveals an attractive path toward developing stable and Li+-conductive interfaces for single-crystal battery materials.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.nanolett.0c03778?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.nanolett.0c03778</a>.Quasi in situ X-ray photoelectron spectroscopy (XPS) characterizations of Zr 3d and Ni 2p (Figure S1), XPS characterizations of O 1s (Figure S2), energy-dispersive spectroscopy (EDS) mapping of 50-ZrO2-700 °C-NCM (Figure S3), cross-sectional scanning electron microscopy (SEM) images of SC-NCM and 5-ZrO2-NCM electrode collected after 50 cycles (Figure S4), reproducible cycle and rate performance of 5-ZrO2-500 °C-NCM (Figure S5), XPS characterizations of F 1s (Figure S6), SEM characterizations of SC-NCM; 5-ZrO2-NCM; 5-ZrO2-500 °C-NCM; 5-ZrO2-700 °C-NCM after 50 cycles (Figure S7), cycle stability of NCM cathodes at 1 C (180 mA/g) in this study compared to literature reports (Table S1) (<a class="ext-link" href="/doi/suppl/10.1021/acs.nanolett.0c03778/suppl_file/nl0c03778_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Enhancing Cell Performance of Lithium-Rich Manganese-Based Materials via Tailoring Crystalline States of a Coating Layer

Suppress voltage decay of lithium-rich materials by coating layers with different crystalline states

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Enhanced Electrochemical Performance of Li1.2Mn0.54Ni0.13Co0.13O2 Cathode Material Coated with Li+-conductive Li2SiO3 for Lithium Ion Batteries

Simultaneous Enhancement of Interfacial Stability and Kinetics of Single-Crystal LiNi 0.6 Mn 0.2 Co 0.2 O 2 through Optimized Surface Coating and Doping

Amorphous Li2ZrO3 nanoparticles coating Li[Li0·17Mn0·58Ni0.25]O2 cathode material for enhanced rate and cyclic performance in lithium ion storage

Insights into the effects of coating and single crystallization on the rate performance and cycle life of LiNi0.9Mn0.1O2 cathode

Enhancing electrochemical performance of lithium-rich manganese-based cathode materials through lithium sulfate coating

Layered/Layered Homostyructure Ion Conductor Coating Strategy for High Performance Lithium Ion Batteries

In-situ formation of Li0.5Mn0.5O coating layer through defect controlling for high performance Li-rich manganese-based cathode material

Understanding the Effects of Surface Modification on Improving the High-Voltage Performance of Ni-rich Cathode Materials

Enhanced Electrochemical Performance of Li[Li0.2ni0.2mn0.6]O-2 Modified by Manganese Oxide Coating for Lithium-Ion Batteries

Enhanced Cathode Performance: Mixed Al 2 O 3 and LiAlO 2 Coating of Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2

Can surface modification be more effective to enhance the electrochemical performance of lithium rich materials?

Improving electrochemical performances of Lithium-rich oxide by cooperatively doping Cr and coating Li3PO4 as cathode material for Lithium-ion batteries

Improving rate capacity and cycling performance of lithium-rich high-Mn Li-1.8[Mn0.7Co0.15Ni0.15]O-2.675 cathode materials by Li2SiO3 coating

Enhancing Electrochemical Performance of LiNi0.6Co0.2Mn0.2O2 by Lithium-ion Conductor Surface Modification

Dual-Element-Modified Single-Crystal LiNi0.6Co0.2Mn0.2O2 As a Highly Stable Cathode for Lithium-Ion Batteries.

Re-understanding the Function Mechanism of Surface Coating: Modified Li-rich Layered Li1.2Mn0.54Ni0.13Co0.13O2 Cathodes with YF3 for High Performance Lithium-Ions Batteries

Electrochemical performance of Li-rich material Li[Li0.2Mn0.54Co0.13Ni0.13]O2 by ZrO2 coating

Nanomaterial coating for layered lithium rich transition metal oxide cathode for lithium-ion battery