Abstract:Steels with sub-micrometre grain sizes usually possess high toughness and strength, which makes them promising for lightweighting technologies and energy-saving strategies. So far, the industrial fabrication of ultrafine-grained (UFG) alloys, which generally relies on the manipulation of diffusional phase transformation, has been limited to steels with austenite-to-ferrite transformation<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="/articles/s41586-021-03246-3#ref-CR3">3</a>. Moreover, the limited work hardening and uniform elongation of these UFG steels<a href="/articles/s41586-021-03246-3#ref-CR1">1</a>,<a href="/articles/s41586-021-03246-3#ref-CR4">4</a>,<a href="/articles/s41586-021-03246-3#ref-CR5">5</a> hinder their widespread application. Here we report the facile mass production of UFG structures in a typical Fe–22Mn–0.6C twinning-induced plasticity steel by minor Cu alloying and manipulation of the recrystallization process through the intragranular nanoprecipitation (within 30 seconds) of a coherent disordered Cu-rich phase. The rapid and copious nanoprecipitation not only prevents the growth of the freshly recrystallized sub-micrometre grains but also enhances the thermal stability of the obtained UFG structure through the Zener pinning mechanism<a href="/articles/s41586-021-03246-3#ref-CR6">6</a>. Moreover, owing to their full coherency and disordered nature, the precipitates exhibit weak interactions with dislocations under loading. This approach enables the preparation of a fully recrystallized UFG structure with a grain size of 800 ± 400 nanometres without the introduction of detrimental lattice defects such as brittle particles and segregated boundaries. Compared with the steel to which no Cu was added, the yield strength of the UFG structure was doubled to around 710 megapascals, with a uniform ductility of 45 per cent and a tensile strength of around 2,000 megapascals. This grain-refinement concept should be extendable to other alloy systems, and the manufacturing processes can be readily applied to existing industrial production lines.

Enhanced Strength and Toughness of Bulk Ultrafine Grained Cu by Nacre-Inspired Lamellar Structure

Microstructure‐Property Relations in the Tensile Behavior of Bimodal Nanostructured Metals

Tuning the Strength-Ductility Synergy of Nanograined Cu Through Nanotwin Volume Fraction

Enhanced Tensile Ductility and Toughness in Nanostructured Cu

High Strength and Utilizable Ductility of Bulk Ultrafine-Grained Cu-Al Alloys

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

Microstructure and Mechanical Properties of Ultrafine-Grained Copper by Accumulative Roll Bonding and Subsequent Annealing

Facile route to bulk ultrafine-grain steels for high strength and ductility

Synthesis of damage-tolerant Cu-matrix composites with nacre-inspired laminate-reticular hierarchical architecture via tuning compositional wettability

Achieving good strength‐plasticity compatibility in Cu composites via carbon nanotube (CNT)‐induced heterogeneous bimodal structure

High tensile ductility in a nanostructured metal

Enhanced strength-ductility synergy in an ultra-strong copper alloy via coherent nanoprecipitates and stress-induced twinning

A novel nanostructure to achieve ultrahigh strength and good tensile ductility of a CoCrFeNiMn high entropy alloy

Excellent Strength-Ductility Synergy of Cu-Al Alloy with a Gradient Nanograined-Nanotwinned Surface Layer

Strong and ductile particulate reinforced ultrafine-grained metallic composites fabricated by flake powder metallurgy

Tensile Properties of in Situ Consolidated Nanocrystalline Cu

Nacre-inspired , strong and ductile cnt / al composites fabricated by flake powder metallurgy

Realizing the combination of high strength and good ductility of Cu matrix composites with CrCoNi reinforcement particles and microlaminated structure

Bamboo-like dual-phase nanostructured copper composite strengthened by amorphous boron framework

Processing and Microhardness of Bulk Cu-Fe Nanocomposites

Regain Strain-Hardening in High-Strength Metals by Nanofiller Incorporation at Grain Boundaries.