Abstract:Commutation failure (CF) and DC blocking (DCB) faults are common occurrences in high-voltage direct current (HVDC) systems, and their impact on the power grid can be significant due to sudden power fluctuations. These issues pose particular challenges in multi-send HVDC systems due to the intricate interaction between AC and DC components. To tackle these challenges, this paper proposes a method for analyzing the peak overvoltage at the converter bus resulting from DC faults in multi-send HVDC systems. The proposed method comprehensively considers the influence of DC/DC coupling and wind turbine low-voltage ride through (LVRT) characteristics on overvoltage. It offers a straightforward approach to calculate the peak overvoltage following a DC fault without the need for complex modeling or dynamic simulation software. By leveraging the equivalent parameters of the AC system and operational parameters of the DC system, the method effectively quantifies the overvoltage. The primary objective of this study is to address multi-send HVDC systems and establish computational formulas that enable a quantitative assessment of transient overvoltage resulting from DC faults. The analysis explores several influencing factors, uncovering that fault-induced overvoltage is influenced by aspects such as system strength and wind turbine reactive power dynamics. In a single-send HVDC system, the level of overvoltage in the system is primarily affected by the short-circuit ratio. A higher short-circuit ratio results in a lower overvoltage level. On the other hand, in multi-send HVDC systems, the overvoltage level is determined by the equivalent impedance of the individual systems. In DC systems where turbines are present in the DC near zone, the overvoltage level at the converter bus is influenced by the power characteristics of the turbines during the LVRT. To validate the accuracy of the proposed method, a comprehensive verification process is conducted. Through this research, the paper aims to contribute to the understanding and management of transient overvoltage in multi-send HVDC systems. By considering relevant factors and employing an equivalent model, the proposed method offers a practical approach for assessing overvoltage and facilitating the design and operation of such systems.

Determination of Operating Conditions of LCC for PCOV Calculation Based on Detailed Analysis of Commutation Overshoot

Current Saturation Analysis of Droop Controlled Voltage Source Converter

Research on Converter Valve Overvoltage Mechanism and Calculation Conditions of ± 800 Kv Converter Station

Commutation Overlap Characteristic Modeling and Stability Analysis of LCC-HVDC in Sending AC Grid

Study on the Influence of Inconsistent Valve Parameters on LCC-HVDC Commutation and Operation

Modeling and Overvoltage Suppression Analysis of Grid-connected Converter with VSG Control Strategy under Commutation Failure

Analysis and Design of Damping Circuit Parameters for LCC Valves Based on Broadband Model

Analysis and Design-Optimization of LCC Resonant Converter Operating under Wide Range Input and Output Voltage

Overvoltage Suppression Under Commutation Failure Based on Improved Voltage-Dependent Current Order Limiter Control Strategy

Overvoltage Mechanism of Converter Valves for HVDC Power Transmission Project from Tianshengqiao to Guangzhou

Impedance Characteristic Analysis and Phase-locked Angle Feedforward-based Stability Improvement for LCC-HVDC in Sending AC Grid

Calculation Method of DC Fault Overvoltage Peak Value for Multi-Send HVDC Systems with Wind Power

A Predictive Method of LCC-HVDC Continuous Commutation Failure Based on Threshold Commutation Voltage Under Grid Fault

Risk Assessment of Commutation Failure Caused by Inrush Current Based on Multi-Principal Elements Modal Analysis

Influence of Over-voltage Condition Brought by HEMP, Lightning Over-voltage and Operating Over-voltage During Commutation Period on Reliability of HVDC Converter Valve

Analysis and Design for Voltage Equalization in RB-IGCT Based Hybrid Commutated Converter Applications

Comprehensive Physical Commutation Characteristic Analysis and Test of Hybrid Line Commutated Converter Based on Physics Compact Model of IGCT

An Improved Decision Tree‐based Method for Evaluating Transient Overvoltage Caused by Commutation Failure in LCC‐HVDC Systems

A Simple Open-loop Soft Startup Method Based on Operation Mode Analysis for LCC Converters Used in High-voltage DC Power Supply

Investigation of a Low-Speed Commutation Voltage Shock Problem in Three-Level ANPC Inverter with Hybrid Modulation Mode

Effectiveness Analysis of Evaluating Continuous Commutation Failure with Short Circuit Ratio