Abstract:With inevitable introduction of Fe in aluminum processing, a method for achieving high-value utilization of iron-bearing aluminum-based alloys is essential. Aluminum–air batteries are among the most promising power sources and have attracted the attention of researchers. In this study, the electrochemical behavior and discharge properties of Al–0.5Fe and Al–0.5Mn–0.5Fe–0.1Sn–xLi (x = 0, 1, 2, and 3 wt %) alloys as Al–air battery anodes are investigated in 4 M NaOH. Using x-ray diffraction (XRD) and scanning electron microscopy (SEM), the constituents and distributions of the main phases are discussed. Alloying improves electrochemical behavior and discharge properties of Al–0.5Fe. The static and dynamic electrochemical experiments indicate that Al–0.5Mn–0.5Fe–0.1Sn–2Li exhibits the best corrosion resistance. The discharge performances of the five alloys show that the average voltages decrease with increasing current density and Li content. Based on the electrochemical and discharge results, Al–0.5Mn–0.5Fe–0.1Sn–2Li is an excellent candidate for use in Al–air battery anodes, reaching a peak anodic efficiency of 77.86% at a relatively high current density of 80 mA cm −2 , with a power density and specific energy of 83.60 mW cm −2 and 1618.06 mW h g −1 , respectively. The optimal discharge performance is attributed to dispersed AlLi particles and the fragmentation effect of AlLi on the long strip-like Al 6 Mn(Fe) phase.

The Role of Microstructural Evolution in Improving Energy Conversion of Al-based Anodes for Metal-Air Batteries

Effect of Annealing Process on Anode Discharge Performance of Aluminum-Air Batteries

Tailoring the microstructure of Mg-Al-Sn-RE alloy via friction stir processing and the impact on its electrochemical discharge behaviour as the anode for Mg-air battery

Microwave-assisted smelting to improve the corrosion and discharge performance of Al-anodes in Al-air batteries

Simultaneous Regulation on Electrolyte Structure and Electrode Interface with Glucose Additive for High-Energy Aluminum Metal-Air Batteries

Surface Evolution of Aluminum Electrodes in Non-Aqueous Aluminum Batteries

Dynamic Al–O Interactions Enable Uniform Al Deposition Toward High Energy-Density and Practical Al Metal Batteries

High performance Al anode for Al-air battery enabled by coordinating In and Sb additions with discharge parameters

Enhancing the Electrochemical Performance of Al-Mg-Sn-Ga Alloy Anode for Al-Air Battery by Solution Treatment

Investigation of the Commercial Aluminum Alloys as Anode Materials for Alkaline Aluminum-air Batteries

Elucidating the dependence of electrochemical behavior and discharge performance on the grain structure of lean Mg-0.3Bi-0.3Ag-0.3In anodes in primary Mg-air battery

Modulation of Al-Zn-0.5Sn-0.5Mn Anode Properties by Trace Sb

Tailoring the discharge performance of extruded Mg-Sm-Al anode for Mg-air battery applications via control of Al content

Effect of microwave melting and subsequent rolling on the corrosion behavior and electrochemical properties of an aluminum anode using response surface methodology

Dissolution of Nanoprecipitate on Aluminum-Alloy Anode for High Discharging Performance in Al Battery Applications

The role of electrocatalytic materials for developing post-lithium metal||sulfur batteries

Regulating electrodeposition morphology in high-capacity aluminium and zinc battery anodes using interfacial metal–substrate bonding

En bloc stapling of renal hilum during laparoscopic nephrectomy and nephroureterectomy.

Reconstructing 3d-Metal Electrocatalysts through Anionic Evolution in Zinc-Air Batteries

Imaging the microstructure of lithium and sodium metal in anode-free solid-state batteries using electron backscatter diffraction

Development of low-carbon energy storage material: Electrochemical behavior and discharge properties of iron-bearing Al–Li-based alloys as Al–air battery anodes