Piezo-phototronic Effect Enhanced Photodetectors Based on MAPbI3 Perovskite

Jiaheng Nie,Yan Zhang,Lijie Li,Jizheng Wang

DOI: https://doi.org/10.1039/c9tc05721h

IF: 6.4

2020-01-01

Journal of Materials Chemistry C

Abstract:A novel piezo-phototronic effect enhanced photodetector based on MAPbI3 polycrystalline perovskite is designed and fabricated with reconfigurable piezoelectric performance.

What problem does this paper attempt to address?

Enhanced Piezoelectricity of MAPbI3 by the Introduction of MXene and Its Utilization in Boosting High-Performance Photodetectors

Gaosi Han,Xiao-Fen Li,Andy Berbille,Yueming Zhang,Xiongxin Luo,Lindong Liu,Longyi Li,Zhong Lin Wang,Laipan Zhu

DOI: https://doi.org/10.1002/adma.202313288

Abstract:Recently, perovskite photodetectors (PDs) are risen to prominence due to substantial research interest. Beyond merely tweaking the composition of materials, a cutting-edge advancement lies in leveraging the innate piezoelectric polarization properties of perovskites themselves. Here, the investigation shows utilizing Ti3C2Tx, a typical MXene, as an intermediate layer for significantly boosting the piezoelectric property of MAPbI3 thin films. This improvement is primarily attributed to the enhanced polarization of the methylammonium (MA+) groups within MAPbI3, induced by the OH groups present in Ti3C2Tx. A flexible PD based on the MAPbI3/MXene heterostructure is then fabricated. The new device is sensitive to a wide range of wavelengths, displays greatly enhanced performance owing to the piezo-phototronic coupling. Moreover, the device is endowed with a greatly reduced response time, down to millisecond level, through the pyro-phototronic effect. The characterization shows applying a -1.2% compressive strain on the PD leads to a remarkable 102% increase in the common photocurrent, and a 76% increase in the pyro-phototronic current. The present work reveals how the emerging piezo-phototronic and pyro-phototronic effects can be employed to design high-performance flexible perovskite PDs.
Efficient Photodiode-Type Photodetectors with Perovskite Thin Films Derived from an MAPbI3 Single-Crystal Precursor

Hong Tao,Haoning Wang,Yuchen Bai,Hongyang Zhao,Qiuming Fu,Zhibin Ma,Hao Long

DOI: https://doi.org/10.1039/d0tc00734j

IF: 6.4

2020-01-01

Journal of Materials Chemistry C

Abstract:This research exhibits an efficient photodetector based on a perovskite photosensitive layer derived from an MAPbI3 single-crystal precursor.
High-Performance Planar-Type Photodetector on (100) Facet of MAPbI3 Single Crystal

Zhipeng Lian,Qingfeng Yan,Qianrui Lv,Ying Wang,Lili Liu,Lijing Zhang,Shilie Pan,Qiang Li,Liduo Wang,Jia-Lin Sun

DOI: https://doi.org/10.1038/srep16563

2015-11-13

Abstract:Recently, the discovery of organometallic halide perovskites provides promising routes for fabricating optoelectronic devices with low cost and high performance. Previous experimental studies of MAPbI3 optoelectronic devices, such as photodetectors and solar cells, are normally based on polycrystalline films. In this work, a high-performance planar-type photodetector fabricated on the (100) facet of a MAPbI3 single crystal is proposed. We demonstrate that MAPbI3 photodetector based on single crystal can perform much better than that on polycrystalline-film counterpart. The low trap density of MAPbI3 single crystal accounts for the higher carrier mobility and longer carrier diffusion length, resulted in a significant performance increasement of MAPbI3 photodetector. Compared with similar planar-type photodetectors based on MAPbI3 polycrystalline film, our MAPbI3 single crystal photodetector showed excellent performance with good stability and durability, broader response spectrum to near-infrared region, about 10(2) times higher responsivity and EQE, and approximately 10(3) times faster response speed. These results may pave the way for exploiting high-performance perovskites photodetectors based on single crystal.
High-Performance Planar-Type Photodetector on (100) Facet of MAPbI 3 Single Crystal

Zhipeng Lian,Qingfeng Yan,Qianrui Lv,Ying Wang,Lili Liu,Lijing Zhang,Shilie Pan,Qiang Li,Liduo Wang,Jia-Lin Sun

DOI: https://doi.org/10.1038/srep16563

IF: 4.6

2015-01-01

Scientific Reports

Abstract:Recently, the discovery of organometallic halide perovskites provides promising routes for fabricating optoelectronic devices with low cost and high performance. Previous experimental studies of MAPbI 3 optoelectronic devices, such as photodetectors and solar cells, are normally based on polycrystalline films. In this work, a high-performance planar-type photodetector fabricated on the (100) facet of a MAPbI 3 single crystal is proposed. We demonstrate that MAPbI 3 photodetector based on single crystal can perform much better than that on polycrystalline-film counterpart. The low trap density of MAPbI 3 single crystal accounts for the higher carrier mobility and longer carrier diffusion length, resulted in a significant performance increasement of MAPbI 3 photodetector. Compared with similar planar-type photodetectors based on MAPbI 3 polycrystalline film, our MAPbI 3 single crystal photodetector showed excellent performance with good stability and durability, broader response spectrum to near-infrared region, about 10 2 times higher responsivity and EQE and approximately 10 3 times faster response speed. These results may pave the way for exploiting high-performance perovskites photodetectors based on single crystal.
Additive Modulated Perovskite Microstructures for High Performance Photodetectors

Zhan Gao,Yifan Zheng,Guancheng Huang,Genjie Yang,Xinge Yu,Junsheng Yu

DOI: https://doi.org/10.3390/mi11121090

IF: 3.4

2020-12-10

Micromachines

Abstract:Organic-inorganic hybrid perovskites have been widely used as light sensitive components for high-efficient photodetectors due to their superior optoelectronic properties. However, the unwanted crystallographic defects of perovskites typically result in high dark current, and thus limit the performance of the device. Herein, we introduce a simple route of microstructures control in MAPbI3 perovskites that associates with introducing an additive of 3,3,4,4-benzophenonetetracarboxylic dianhydridean (BPTCD) for crystallization adjustment of the perovskite film. The BPTCD additive can facilitate the formation of high-quality perovskite film with a compact and nearly pinhole-free morphology. Through characterizing the molecular interactions, it was found that the carbonyl groups in BPTCD is the key reason that promoted the nucleation and crystallization of MAPbI3. As a result, we obtained high-efficient and stable perovskite photodetectors with low dark current of 9.98 × 10−8 A at −0.5 V, an on/off ratio value of 103, and a high detectivity exceeding 1012 Jones over the visible region.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
Large-Area Periodic Organic-Inorganic Hybrid Perovskite Nanopyramid Arrays for High-Performance Photodetector and Image Sensor Applications

Xiuzhen Xu,Wenfei Liu,Zhenkai Ji,Dandan Hao,Wenyuan Yan,Zilong Ye,Yan Hu,Minghe Fang,Changchun Wang,Liang Ma,Jia Huang,Xiaobin Xu,Paul S. Weiss

DOI: https://doi.org/10.1021/acsmaterialslett.1c00298

IF: 11.4

2021-01-01

ACS Materials Letters

Abstract:The rapid growth of organic-inorganic hybrid perovskite materials (such as methylammonium lead triiodide, MAPbI(3)) in photoelectric applications has prompted investigations of novel strategies to improve photodetection performance. Although a few surface nanofabrication methods have been applied to texture perovskite thin films to enhance light trapping, it remains challenging to pattern large-area periodic perovskite nanoarrays in a tunable and scalable manner. In this work, we report a facile and low-cost approach to fabricate large-area SiO2/Si nanopyramids arrays through nanosphere lithography. These nanopyramids arrays are used to pattern MAPbI(3) thin films. We find that the introduction of nanopyramid arrays enhances the light intensity within the perovskite film, which is confirmed by light absorption tests and optical simulations. As a result, the photodetectors based on MAPbI(3) with nanopyramid structures show excellent responsivity of 28.8 +/- 1.0 A/W and detectivity of (3.5 +/- 0.1) x 10(11) Jones at 650 nm. The photoresponse of the photodetector to pulsed light is highly stable and reproducible, with rise and decay times of similar to 0.7 and 1.1 ms, respectively. They also have a broader light sensitivity range from ultraviolet to infrared light, i.e., 340 nm to 1100 nm, compared to those without nanostructures. Finally, we demonstrate a prototype image sensor using these photodetector arrays.
A Self‐Powered Photodetector Based on MAPbI 3 Single‐Crystal Film/n‐Si Heterojunction with Broadband Response Enhanced by Pyro‐Phototronic and Piezo‐Phototronic Effects

Zheng Yang,Huan Wang,Linjuan Guo,Qing Zhou,Yansong Gu,Fangtao Li,Shuang Qiao,Caofeng Pan,Shufang Wang

DOI: https://doi.org/10.1002/smll.202101572

IF: 13.3

2021-07-01

Small

Abstract:Pyro-phototronic and piezo-phototronic effect have shown their important roles for high performance heterojunction-based photodetectors (PDs). Here, a coupling effect of pyro-phototronic and piezo-phototronic effect is utilized to fabricate a self-powered and broadband PD based on the MAPbI3 single-crystal film/n-Si heterojunction. First, by using the pyro-phototronic effect derived from MAPbI3, the maximum photoresponsivity of the self-powered PD is 1.5 mA W−1 for 780 nm illumination, which is enhanced by more than 20 times in consideration of the relative peak-to-peak output current. Light-induced temperature change in MAPbI3 film will create pyro-charges distributed at heterojunction interface, resulting in a downward bending of the energy band, facilitating the transport of photon-generated electrons and holes, and generating spike-like output currents. Second, piezo-phototronic effect is further introduced by applying vertical pressures onto the PD. With a vertical pressure of 155 kPa, the responsivity can be improved by more than 120% compared to the condition with no pressure. The overall enhancement is due to the piezo-phototronic and pyro-phototronic coupling effects which utilize the polarization charges to modulate the band structure of heterojunction. These results provide a promising approach to develop high-performance self-powered and broadband perovskite-based PDs by coupling pyro-phototronic and piezo-phototronic effect.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
A high performance CsPbBr3 microwire based photodetector boosted by coupling plasmonic and piezo-phototronic effects

Zheng Yang,Mingming Jiang,Linjuan Guo,Guofeng Hu,Yansong Gu,Jianguo Xi,Zhihao Huo,Fangtao Li,Shufang Wang,Caofeng Pan

DOI: https://doi.org/10.1016/j.nanoen.2021.105951

IF: 17.6

2021-07-01

Nano Energy

Abstract:Lead halide perovskites have attracted much attention in photodetector fabrication. Up to now, several strategies have been used to modulate the device performance. Here, P3HT-CsPbBr3 monocrystalline microwires based photodetectors are demonstrated by coupling LSPR and piezo-phototronic effects. The photocurrent, response speed and recovery speed under 532 nm laser illumination were increased to nearly 3.5, 70 and 8.4 times when decorated with Au NCs and applied with a compressive strain of -0.29%, respectively. The enhancement of performances can be attributed to the increased light absorption caused by LSPR effect and the enhanced separation of photo-generated holes at the heterojunction interface caused by piezo-phototronic effect. This work suggests that all-inorganic perovskites CsPbBr3 based photodetectors can be significantly enhanced by coupling plasmonic and piezo-phototronic effects. This strategy can be used to modulate the performance of optoelectronic devices based on other piezoelectric materials.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
High-Detectivity and Stable Planar MAPbI₃/IDT-BT Photodetectors with Assisted MoO₃ Interlayer

Keyang Zhao,Jianxiong Zou,Fanming Huang,Tian,Zhibin Shao,Wei Tian,Junhao Chu,Wenwu Li

DOI: https://doi.org/10.1109/ted.2021.3123560

IF: 3.1

2021-01-01

IEEE Transactions on Electron Devices

Abstract:Composited with electronic functional materials is an effective way to improve the performance and stability of organic–inorganic hybrid halide perovskite photodetectors. Herein, a planar photoconductive photodetector based on a CH3NH3PbI3 (MAPbI3)/IDT-BT/MoO3 structure was designed and fabricated. Indacenodithiophene-co-benzothiadiazole (IDT-BT) and MoO3 layers are beneficial for photogenerated holes transmission and improve the dissociation efficiency of photogenerated electron–hole pairs. On the other hand, MoO3 as an electron-blocking layer can suppress the dark current. The device displays a fast response time of less than 7 ms, a high responsivity of 11.6 AW−1, and an ultrahigh detectivity up to $5.2\times10$ 13 Jones. In addition, the IDT-BT layer can isolate MAPbI3 from oxygen and water, thus increasing the stable lifetime of devices to more than 20 days. These parameters are several times higher than pristine MAPbI3 photoconductive photodetectors. These results can offer a feasible and effective method for integrating the composite material to improve the performance of perovskite-based devices.
Ultrasensitive Photodetectors Based on Island-Structured CH3NH3PbI3 Thin Films.

Yin Zhang,Juan Du,Xiaohan Wu,Guoqian Zhang,Yingli Chu,Dapeng Liu,Yixin Zhao,Ziqi Liang,Jia Huang

DOI: https://doi.org/10.1021/acsami.5b05221

IF: 9.5

2015-01-01

ACS Applied Materials & Interfaces

Abstract:CH3NH3PbI3 perovskite-based optoelectronics have attracted intense research interests recently because of their easy fabrication process and high power conversion efficiency. Herein, we report a novel photodetector based on unique CH3NH3PbI3 perovskite films with island-structured morphology. The light-induced electronic properties of the photodetectors were investigated and compared to those devices based on conventional compact CH3NH3PbI3 films. The island-structured CH3NH3PbI3 photodetectors exhibited a rapid response speed (<50 ms), good stability at a temperature of up to 100 °C, a large photocurrent to dark current ratio (Ilight/Idark > 1 × 10(4) under an incident light of ∼6.59 mW/cm(2), and Ilight/Idark > 1 × 10(2) under low incident light ∼0.018 mW/cm(2)), and excellent reproducibility. Especially, the performance of the island-structured devices markedly exceed that of the conventional compact CH3NH3PbI3 thin-film devices. These excellent performances render the island-structured device to be potentially applicable for a wide range of optoelectronics.
High-Detectivity and Stable Planar MAPbI3/IDT-BT Photodetectors With Assisted MoO3 Interlayer

Keyang Zhao,Jianxiong Zou,Fanming Huang,Tian Tian,Zhibin Shao,Wei Tian,Junhao Chu,Wenwu Li

DOI: https://doi.org/10.1109/ted.2021.3123560

IF: 3.1

2021-12-01

IEEE Transactions on Electron Devices

Abstract:Composited with electronic functional materials is an effective way to improve the performance and stability of organic–inorganic hybrid halide perovskite photodetectors. Herein, a planar photoconductive photodetector based on a CH3NH3PbI3 (MAPbI3)/IDT-BT/MoO3 structure was designed and fabricated. Indacenodithiophene-co-benzothiadiazole (IDT-BT) and MoO3 layers are beneficial for photogenerated holes transmission and improve the dissociation efficiency of photogenerated electron–hole pairs. On the other hand, MoO3 as an electron-blocking layer can suppress the dark current. The device displays a fast response time of less than 7 ms, a high responsivity of 11.6 AW−1, and an ultrahigh detectivity up to $5.2 imes10$ 13 Jones. In addition, the IDT-BT layer can isolate MAPbI3 from oxygen and water, thus increasing the stable lifetime of devices to more than 20 days. These parameters are several times higher than pristine MAPbI3 photoconductive photodetectors. These results can offer a feasible and effective method for integrating the composite material to improve the performance of perovskite-based devices.

engineering, electrical & electronic,physics, applied
Effective Piezo‐Phototronic Enhancement of Flexible Photodetectors Based on 2D Hybrid Perovskite Ferroelectric Single‐Crystalline Thin‐Films (Adv. Mater. 32/2021)

Ran Ding,Yongxin Lyu,Zehan Wu,Feng Guo,Weng Fu Io,Sin‐Yi Pang,Yuqian Zhao,Jianfeng Mao,Man‐Chung Wong,Jianhua Hao

DOI: https://doi.org/10.1002/adma.202170252

IF: 29.4

2021-08-01

Advanced Materials

Abstract:PhotodetectorsIn article number 2101263, Jianhua Hao and co-workers report the use of ferroelectric EA4Pb3Br10 single-crystalline thin-films to broaden perovskite photodetection applications with piezo-phototronic effect enhanced behavior. The coupling of ferroelectric spontaneous polarization and the piezoelectric effect, as well as photoexcitation and semiconductor behaviors endow the EA4Pb3Br10-based flexible photodetectors with a strain-modulated capability, giving rise to an effective enhancement of photodetection performance via the piezo-phototronic effect.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Highly controllable synthesis of MAPbI3 perovskite nanocrystals with long carrier lifetimes and narrow band gap for application in photodetectors

Tao Wang,Sumin Hou,Huafang Zhang,Yi Yang,Wen Xu,Tianyong Ao,Miao Kang,Gencai Pan,Yanli Mao

DOI: https://doi.org/10.1016/j.jallcom.2021.159589

IF: 6.2

2021-01-01

Journal of Alloys and Compounds

Abstract:Low-dimensional organic-inorganic hybrid perovskite materials have attracted much attention in photoelectric devices due to their exotic performance in optoelectronics compared with their bulk and thin-film counterparts. In this article, using a simple ligand-assisted deposition method, we successfully synthesized uniform methylammonium lead iodide (MAPbI(3)) perovskite nanorods, nanotriangles and nanocubes, and investigated their photoelectric properties after fabricated into photodetectors (PDs) on SiO2/Si substrates. It is found that the synthesized MAPbI(3) nanorods not only have extremely small optical band gap (minimum of similar to 1.36 eV), but also have long photoluminescence (PL) lifetime (longest of similar to 7.81 mu s) and high absolute PL quantum yields (maximum of similar to 45%), and the PL lifetime is more than about one order of magnitude higher than that the reported previously. The PDs based on MAPbI(3) nanorods presented a wide spectral response "window" from 350 to at least 950 nm, and exhibited a photoresponsivity of 12.2 mA/W, a detectivity of 2.67 x 10(11) Jones, the on/off ratio of more than 800, the rise/decay time constants of 18/25 ms, under the excitation at 405 nm. Further analysis suggests that the dramatically improved photo-electric conversion properties of the nanorods PDs could be closely related with their morphology dependent properties, including bandgap, PL lifetime, trap density (n(trap)) and carrier concentration. These results provide a simple and effective method for preparing different morphology low-dimensional MAPbI(3), and discuss the mechanism of morphology-dependent photoelectric performance of PDs, which is of great significance for potential applications in the field of photoelectronic devices. (C) 2021 Elsevier B.V. All rights reserved.
Ferro-pyro-phototronic effect enhanced self-powered, flexible and ultra-stable photodetectors based on highly crystalized 1D/3D ferroelectric perovskite film

Zheng Yang,Xiaoli Li,Linjie Gao,Wei Zhang,Xinzhan Wang,Haixu Liu,Shufang Wang,Caofeng Pan,Linjuan Guo

DOI: https://doi.org/10.1016/j.nanoen.2022.107743

IF: 17.6

2022-11-01

Nano Energy

Abstract:Self-powered and flexible perovskite photodetectors are holding great promise owing to their potential for high-performance wearable and portable optoelectronic applications. The light-induced ferro-pyro-phototronic effect can boost the performances of ferroelectric materials-based photodetector systems significantly. However, the utilization of the ferro-pyro-phototronic effect in polycrystalline halide perovskites films-based flexible photodetectors is rarely mentioned. Here, a ferro-pyro-phototronic effect boosted self-powered, flexible, and ultra-stable photodetector based on 1D/3D mixed perovskite ferroelectric film/P3HT heterojunction is demonstrated. By employing Pb(SCN)2 as lead source to partially for fabricating high-quality MAPbI3 film and incorporating 1D ferroelectric perovskite TMIMPbI3, the overall optoelectronic performances were largely enhanced, with a low dark current of 7 × 10−9 A, a responsivity of 6.6 mA/W and a detectivity of 5 × 109 Jones. The PDs displayed good folding endurance, and anti-humidity stability. The excellent performance is attributed to the reduced trap-density and enhanced pyro-phototronic effect induced by improved crystallinity and introduced ferroelectricity.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
High performance photodetectors based on solution-processed epitaxial grown hybrid halide perovskites.

Li Ji,Hsien-Yi Hsu,Jack C Lee,Allen J Bard,Edward T Yu

DOI: https://doi.org/10.1021/acs.nanolett.7b04445

IF: 10.8

2018-01-01

Nano Letters

Abstract:Hybrid organic-inorganic halide perovskites (HOIPs) have recently attracted tremendous attention because of their excellent semiconducting and optoelectronic properties, which exist despite their morphology and crystallinity being far inferior to those of more mature semiconductors, such as silicon and III-V compound semiconductors. Heteroepitaxy can provide a route to achieving high-performance HOIP devices when high crystalline quality and smooth morphology are required, but work on heteroepitaxial HOIPs has not previously been reported. Here, we demonstrate epitaxial growth of methylammonium lead iodide (MAPbI(3)) on single crystal KCl substrates with smooth morphology and the highest carrier recombination lifetime (similar to 213 ns) yet reported for nonsingle crystalline MAPbI(3). Experimental Raman spectra agree well with theoretical calculations, presenting in particular a sharp peak at 290 cm(-1) for the torsional mode of the organic cations, a marker of orientational order and typically lacking in previous reports. Photodetectors were fabricated showing excellent performance, confirming the high quality of the epitaxial MAPbI(3) thin films. This work provides a new strategy to enhance the performance of all HOIPs-based devices.
Perovskite Photodetectors Based on p-i-n Junction With Epitaxial Electron-Blocking Layers

Yubing Xu,Xin Wang,Yuzhu Pan,Yuwei Li,Elias Emeka Elemike,Qing Li,Xiaobing Zhang,Jing Chen,Zhiwei Zhao,Wei Lei

DOI: https://doi.org/10.3389/fchem.2020.00811

IF: 5.5

2020-09-15

Frontiers in Chemistry

Abstract:Organic-inorganic hybrid perovskite single crystals (PSCs) have been emerged as remarkable materials for some optoelectronic applications such as solid-state photodetectors, solar cells and light emitting diodes due to their excellent optoelectronic properties. To decrease the dark current, function layers based on spin-coating method are frequently requested for intrinsic PSCs to block the injected current by forming energy barrier. However, the amorphous function layers suffer from small carrier mobility and high traps density, which limit the speed of the photoelectric response of perovskite devices. This work supposes to grow thick MAPbBr3 and MAPbI3 mono-crystalline thin films on the surface of intrinsic MAPbBr2.5Cl0.5 PSCs substrate by a heteroepitaxial growth technique to act as electron-blocking layers. Meanwhile, C60 and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) layers are deposited on the opposite surface of substrate PSCs by spin-coating method to block injected holes. This Au-MAPbI3-MAPbBr3-MAPbBr2.5Cl0.5PSCs-C60-PCBM-Ag heterostructure can be used as excellent X-ray photodetector (XPD) due to its low dark current density of 6.97 × 10−11 A cm−2 at −0.5 V bias, high responsivity of 870 mA/W at −100 V bias and X-ray sensitivity as high as 59.7 μC mGy−1 cm−2 at −50 V bias.

chemistry, multidisciplinary
BEHAVIORS OF PHOTOCONDUCTIVE DETECTORS BASED ON MAPbI(3) PEROVSKITE FILMS

Genyuan Yu,Lisha Feng,Lu Meng,Zhizhen Ye,Jianguo Lu

DOI: https://doi.org/10.1142/s0218625x18500579

2018-01-01

Surface Review and Letters

Abstract:The CH3NH3PbI3 films were synthesized by a facile low-cost solution process and were used to fabricate photoconductive detectors. The perovskite photodetector is very sensitive to light, with a high responsivity of 5.51[Formula: see text]mA/W and a sensitivity of 50 at 5[Formula: see text]V under 350[Formula: see text]nm light illumination. The device exhibits the fast rise and decay processes with similar appearance, and the relaxation time constants are 270 and 300[Formula: see text]ms, respectively. The photo-current shows an evident saturation, without further increase for prolonging the illumination period. The perovskite photodetectors display high responsive performances to short-wavelength lights. This study is expected to provide a fundamental knowledge of perovskite photodetectors with high speed and repeatability for practical applications.
Preparation and Testing of Anisotropic MAPbI3 Perovskite Photoelectric Sensors.

Zhenhao Zhao,Yahui Li,Yunjie Du,Lei Zhang,Jinquan Wei,Feng Lin

DOI: https://doi.org/10.1021/acsami.0c10062

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:Perovskite structures of organic and inorganic halides are peculiar structures with many interesting properties. Using their photoelectric effect, the structures have been used in photocells, photoelectric sensors, and light-emitting diodes. In conventional perovskite film crystallization, which is a one-step method, the MAPbI3 crystals form disordered needlelike crystals at room temperature. Such needlelike crystal films have rough surfaces and low coverage to the substrate, resulting in insignificant photoelectric effects. With the assistance of an electric field and three-dimensional (3D) printing, the direction of the perovskite needlelike crystal can be arranged to make it orderly. In this way, the photoelectric sensor of the ordered MAPbI3 perovskite needlelike crystal film can be prepared. This sensor has high sensitivity, high stability, and high response speed. Moreover, it has anisotropy and higher photoelectric sensitivity in the direction perpendicular to the needle crystal. Most interestingly, the sensors respond differently to polarized light in different directions, and this effect can be used to detect the direction and degree of polarization of polarized light.
Effective Piezo‐Phototronic Enhancement of Flexible Photodetectors Based on 2D Hybrid Perovskite Ferroelectric Single‐Crystalline Thin‐Films

Ran Ding,Yongxin Lyu,Zehan Wu,Feng Guo,Weng Fu Io,Sin‐Yi Pang,Yuqian Zhao,Jianfeng Mao,Man‐Chung Wong,Jianhua Hao

DOI: https://doi.org/10.1002/adma.202101263

IF: 29.4

2021-06-27

Advanced Materials

Abstract:2D hybrid perovskites are very attractive for optoelectronic applications because of their numerous exceptional properties. The emerging 2D perovskite ferroelectrics, in which are the coupling of spontaneous polarization and piezoelectric effects, as well as photoexcitation and semiconductor behaviors, have great appeal in the field of piezo-phototronics that enable to effectively improve the performance of optoelectronic devices via modulating the electro-optical processes. However, current studies on 2D perovskite ferroelectrics focus on bulk ceramics that cannot endure irregular mechanical deformation and limit their application in flexible optoelectronics and piezo-phototronics. Herein, we synthesize ferroelectric EA4Pb3Br10 single-crystalline thin-films (SCFs) for integration into flexible photodetectors. The in-plane multiaxial ferroelectricity is evident within the EA4Pb3Br10 SCFs through systematic characterizations. Flexible photodetectors based on EA4Pb3Br10 SCFs are achieved with an impressive photodetection performance. More importantly, optoelectronic EA4Pb3Br10 SCFs incorporated with in-plane ferroelectric polarization and effective piezoelectric coefficient show great promise for the observation of piezo-phototronic effect, which is capable of greatly enhancing the photodetector performance. Under external strains, the responsivity of the flexible photodetectors can be modulated by piezo-phototronic effect with a remarkable enhancement up to 284%. Our findings shed light on the piezo-phototronic devices and offer a promising avenue to broaden functionalities of hybrid perovskite ferroelectrics.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Self‐Powered and Flexible Photodetector with High Polarization Sensitivity Based on MAPbBr3–MAPbI3 Microwire Lateral Heterojunction

Shun-Xin Li,Hong Xia,Lei Wang,Xiang-Chao Sun,Yang An,He Zhu,Ben-Feng Bai,Hong-Bo Sun

DOI: https://doi.org/10.1002/adfm.202206999

IF: 19

2022-01-01

Advanced Functional Materials

Abstract:Assembling perovskites into heterojunctions is an effective approach to achieve high‐performance photodetectors. Compared with vertical heterojunctions, in lateral heterojunction‐based photodetectors, the reflection loss is reduced because the active layer is in direct contact with light resulting in higher performance and better stability. However, lateral perovskite–perovskite heterojunctions are difficult to achieve using solution methods because the first formed film is easily dissolved by the solvent of the second precursor. In this study, a two‐step imprinting method is developed to fabricate lateral MAPbI3–MAPbBr3 microwire heterojunctions and realize a high‐performance photodetector with a responsivity and detectivity of 1207 A W−1 and 2.78 × 1013 Jones, respectively. At 0 V bias, the device exhibits a responsivity of up to 233 A W−1, which is more than double the previously reported best results. The high‐quality heterojunction endows the photodetectors with ultra‐high polarization sensitivity (Imax/Imin = 8.2) and long‐term stability, retaining 88.2% of its initial performance even after being exposed to air for 391 d.

Piezo-phototronic Effect Enhanced Photodetectors Based on MAPbI3 Perovskite

Enhanced Piezoelectricity of MAPbI3 by the Introduction of MXene and Its Utilization in Boosting High-Performance Photodetectors

Efficient Photodiode-Type Photodetectors with Perovskite Thin Films Derived from an MAPbI3 Single-Crystal Precursor

High-Performance Planar-Type Photodetector on (100) Facet of MAPbI3 Single Crystal

High-Performance Planar-Type Photodetector on (100) Facet of MAPbI 3 Single Crystal

Additive Modulated Perovskite Microstructures for High Performance Photodetectors

Large-Area Periodic Organic-Inorganic Hybrid Perovskite Nanopyramid Arrays for High-Performance Photodetector and Image Sensor Applications

A Self‐Powered Photodetector Based on MAPbI 3 Single‐Crystal Film/n‐Si Heterojunction with Broadband Response Enhanced by Pyro‐Phototronic and Piezo‐Phototronic Effects

A high performance CsPbBr3 microwire based photodetector boosted by coupling plasmonic and piezo-phototronic effects

High-Detectivity and Stable Planar MAPbI₃/IDT-BT Photodetectors with Assisted MoO₃ Interlayer

Ultrasensitive Photodetectors Based on Island-Structured CH3NH3PbI3 Thin Films.

High-Detectivity and Stable Planar MAPbI3/IDT-BT Photodetectors With Assisted MoO3 Interlayer

Effective Piezo‐Phototronic Enhancement of Flexible Photodetectors Based on 2D Hybrid Perovskite Ferroelectric Single‐Crystalline Thin‐Films (Adv. Mater. 32/2021)

Highly controllable synthesis of MAPbI<sub>3</sub> perovskite nanocrystals with long carrier lifetimes and narrow band gap for application in photodetectors

Ferro-pyro-phototronic effect enhanced self-powered, flexible and ultra-stable photodetectors based on highly crystalized 1D/3D ferroelectric perovskite film

High performance photodetectors based on solution-processed epitaxial grown hybrid halide perovskites.

Perovskite Photodetectors Based on p-i-n Junction With Epitaxial Electron-Blocking Layers

BEHAVIORS OF PHOTOCONDUCTIVE DETECTORS BASED ON MAPbI(3) PEROVSKITE FILMS

Preparation and Testing of Anisotropic MAPbI3 Perovskite Photoelectric Sensors.

Effective Piezo‐Phototronic Enhancement of Flexible Photodetectors Based on 2D Hybrid Perovskite Ferroelectric Single‐Crystalline Thin‐Films

Self‐Powered and Flexible Photodetector with High Polarization Sensitivity Based on MAPbBr3–MAPbI3 Microwire Lateral Heterojunction