Abstract:The microstructure and corrosion resistance of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions were investigated. The composition was detected by X-ray fluorescence (XRF), and the microstructure was analyzed by optical microscopy (OM) and scanning electron microscope (SEM) equipped with energy-dispersive spectroscopy (EDS). The corrosion behavior was investigated by hydrogen evolution tests, weight loss tests and electrochemical measurements. The Mg–0.5Zn–0.2Ca–0.2Ce alloy has much better corrosion resistance compared with the commercial AZ31 sheet, which can be attributed to its dispersive second phases and protective corrosion products film on the alloy surface. Moreover, the as-rolled Mg–0.5Zn–0.2Ca–0.2Ce alloy shows much better corrosion resistance compared with the as-extruded Mg–0.5Zn–0.2Ca–0.2Ce alloy. This can be due to three aspects: The as-rolled alloy has smaller grain size; the as-rolled alloy has lower (10\({\bar{1}}\)0)/(11\({\bar{2}}\)0) texture intensity; the residual stress of the as-rolled alloy is eliminated during the annealing process, but large residual stress exists in the as-extruded alloy produced by the extrusion process.

Corrosion and Discharge Performance of Mg-2Zn-0.5Ce-0.5Mn-0.2Ca Alloy in NaCl Solution

Electrochemical Investigations on AZ Series Magnesium Alloys as Anode Materials in a Sodium Chloride Solution

Corrosion Behaviour and Discharge Properties of Extruded Mg-Zn-Ca Anodes for Primary Mg-air Batteries

Discharge and corrosion behavior of Mg–2Zn–Mn–xY alloys as the anode for Mg-air battery

A corrosion resistant die-cast Mg-9Al-1Zn anode with superior discharge performance for Mg-air battery

The Solute Cerium to Enhance Corrosion Resistance of Magnesium Anode in 3.5% NaCl Solution

Effects of Ca addition on microstructure, electrochemical behavior and magnesium-air battery performance of Mg-2Zn-xCa alloys

Effects of Zn/Ca alloying on the Second Phase, Corrosion Behavior and Mg‐air Battery Anodic Performance of Mg‐1Sn‐based Alloys

Linking the discharge behavior and microstructure of ternary Mg–Ca–Zn alloy anodes for magnesium-air cells

Establishment of electrode potential-composition plot of Al-Mg-Zn alloys and sacrificial anode protection tests

Microstructure and corrosion properties of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions

Alloy Alleviating Galvanic Corrosion Enables Uniform Mg Deposition with Long Cycle Life

The semi-continuous (Mg,Al) 2 Ca second phase on Mg-Al-Ca-Mn alloys as an efficient anti-corrosion anode for Mg-air batteries

Effect of Ce content on performance of AZ31 magnesium alloy anode in air battery

Effects of trace amounts of Sn, Ca, and Cu on the electrochemical properties and discharge performance of Mg-2Zn-1Gd-0.5Zr as an anode for Mg-air battery

Effect of Sn/Ca Mass Ratio on the Second Phase, Corrosion Behavior and Discharge Performance of Mg–xSn–1Ca Mg–Air Battery Anodes

Corrosion Behavior and Mechanical Properties of Mg–Zn–Ca Amorphous Alloys

Tailoring the electrochemical behavior and discharge performance of Mg–Al–Ca–Mn anodes for Mg-air batteries by different extrusion ratios

Corrosion Behavior of Mg-Zn-Y-Zr Alloys in Nacl Solution

A micro-alloyed Mg-Zn-Ge alloy as promising anode for primary Mg-air batteries

Electrochemical properties of AZ31 and NZ30K alloys as anode materials for magnesium battery