Abstract:Mg–6.0 Zn–2.0 Yb–0.5 Zr (wt.%) alloy exhibits excellent strength and ductility synergy after thermomechanical and heat treatment. Unfortunately, the hot workability and microstructure evolution under specific deformation regimes remain uncertain to date. In this work, the constitutive model and hot processing maps were established based on a series of isothermal compression tests. A detailed examination of deformation microstructures at different processing regimes revealed that the hot workability and correlated microstructure development were deformation condition dependent. When compressed at lower strain rates and higher deformation temperatures, the softening was promoted by dynamic recrystallization (DRX) and the prevalence of discontinuous dynamic recrystallization (DDRX) generally resulted in a complete DRX process with coarse grains and much-intensified texture. On the contrary, work hardening was improved with increasing dislocation density, and the continuous DRX (CDRX) may control the partial DRX progress, often presenting a much-refined microstructure with a more dispersed texture. Interestingly, a low strain rate of 0.001 s −1 and a moderate deformation temperature of 300 °C effectively balanced the nucleation rate and grain growth to finally achieve a much refined and relatively homogeneous grain structure. Further investigation concerning the activation energy suggested that the workability improved with increasing strain rate and temperature. Enhanced hot workability at most deformation regimes was achieved due to a lower average activation energy Q value in comparison with that of 1.0 wt.% Yb alloyed ZK60 counterpart, which was likely due to a higher activity of non-basal slips achieved in this alloy.

Microstructural Evolutions and Mechanical Properties of Mg-xY-2Nd-0.2Zn-0.5Zr (x = 0, 2, 4, 6 and 8) Alloy under Hot Compression

Hot compression behavior and microstructure evolution of Mg-Gd-Y-Zn-Zr alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Dynamic Recrystallization Behavior and Hot Workability of Mg–2.0Zn–0.3Zr–0.9Y Alloy by Using Hot Compression Test

Hot workability and microstructure of Mg–6.0 Zn–2.0 Yb–0.5 Zr magnesium alloy

Hot Compression Deformation Behavior of Mg-9Gd-2.9Y-1.9Zn-0.4Zr-0.2Ca (wt%) Alloy

Hot Deformation Behavior and Microstructure Evolutions of As-Forged Mg-Gd-Y-Zn-Zr Alloy

Dynamic Recrystallization Behaviors of a Mg-4Y-2Nd-0.2Zn-0.5Zr Alloy and the Resultant Mechanical Properties after Hot Compression

Hot Deformation and Dynamic Recrystallization Behaviors of Mg–Gd–Y–Zr Alloy

Thermal Deformation Behavior and Processing Maps of As-Homogenized Mg-5.8 Zn-0.5 Zr-1.0 Yb Alloy

High Temperature Compressive Deformation Behavior of an Extruded Mg–8Gd–3Y–0.5Zr (wt.%) Alloy

Hot Deformation and Work Hardening Behavior of an Extruded Mg–Zn–Mn–Y Alloy

Hot compression behavior, simulation verification and dynamic recrystallization mechanism of Mg-Gd-Y-Zr alloy

Deformation Behavior, Microstructure Evolution and Hot Workability of Mg-3.7Gd-2.9Y-0.7Zn-0.7Zr Alloy

Dynamic Recrystallization Behavior of Mg-Gd-Y-Zr Alloy During Hot Compression

Compressive Properties and Microstructure Evolution of Aging Mg-Gd-Y-Zr Magnesium Alloys

Hot Compressive Deformation Behaviors of Mg–10Gd–3Y–0.5Zr Alloy

Microstructure, Texture, and Enhanced Mechanical Properties of an Extruded Mg–rare Earth Alloy after Hot Compression

Flow softening and dynamic recrystallization behavior of a Mg-Gd-Y-Nd-Zr alloy under elevated temperature compressions

Mechanical Behavior and Microstructure Evolution of Mg-Gd-Y-Zn-Zr Alloy during Multipass Hot Compression Deformation