Abstract:Vapor deposition of perovskite solar cells (PSCs) has attracted considerable interest for its dry processing characteristics. However, a two-step sequential vapor deposition method suffers from ineffective conversion of PbI2 to perovskite with reasons still unclear. In this report, we carefully investigated the crystallization orientation of PbI2 films deposited by physical vapor deposition via synchrotron grazing-incidence wide-angle X-ray scattering (GIWAXS) and observed an asymmetric scattering pattern with respect to the qz-axis. The observed oriented morphology and texture hinder the diffusion of MAI molecules in the PbI2 films synthesized by vapor deposition, resulting in over 15% PbI2 remaining at the buried interface after reaction with MAI vapor. As a result, the MAPbI3 synthesized in this way was also highly oriented, especially in the surface layers. Surface fumigation (SF) step was introduced to decrease the orientational anisotropy of PbI2, which successfully breaks the diffusion barriers of MAI molecules by forming a complex layer on the PbI2 surface with polar solvent vapors, like dimethyl sulfoxide or 1,3-dimethyl-2-imidazolidinone. We infer that the SF treatment changes the vapor–solid reaction mechanism from reaction–crystallization to dissolution–recrystallization, which largely promotes the conversion of PbI2 to perovskite. Defects were reduced in perovskite synthesized in this way, and a p-i-n device with 19.56% efficiency was fabricated, which is among the highest efficiencies reported for sequential-vapor-deposited PSCs. Notably, this method enables the fabrication of conformal perovskite layers on uneven substrates. An exemplary PSC showing efficiency of 8.93% was fabricated on a precurved substrate. We believe that the method is applicable to the fabrication of tandem or curved PSCs that are compatible with wearable or building/autocar-integrated photovoltaics in the future.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12283.XRD, SEM, GIWAXS, coordination rate test, diagram of saturated vapor pressure, stability of different complexes, MAI loss rate, film color changes during the reaction, comparison of the efficiency, J–V curves, steady-state output at the maximum power point, the corresponding external quantum efficiency (EQE) spectra in the literature (PDF)This article has not yet been cited by other publications.

Self-Formed Pbi2-Dmso Adduct For Highly Efficient And Stable Perovskite Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

High-Performance Perovskite Solar Cells Fabricated by a Hybrid Physical–Chemical Vapor Deposition

Octylammonium Octyldithiocarbamate Assisted Modulation of Crystallization and Doping of In Situ‐Generated Lead Sulfide for Efficient and Highly Stable Carbon‐Based CsPbIBr2 Solar Cells

Enhanced Efficiency and Stability of Perovskite Solar Cells by 2D Perovskite Vapor-Assisted Interface Optimization

Vapor-assisted deposition of CsPbIBr2 films for highly efficient and stable carbon-based planar perovskite solar cells with superior Voc

Self‐Polymerization of Monomer and Induced Interactions with Perovskite for Highly Performed and Stable Perovskite Solar Cells

PbI6 Octahedra Stabilization Strategy Based on π‐π Stacking Small Molecule Toward Highly Efficient and Stable Perovskite Solar Cells

Enhanced efficiency of planar perovskite solar cells via a two-step deposition using DMF as an additive to optimize the crystal growth behavior

Perovskite Solar Cells Fabricated by Using an Environmental Friendly Aprotic Polar Additive of 1,3-Dimethyl-2-imidazolidinone

Surface-Orientation Elimination of Vapor-Deposited PbI 2 Flakes for Efficient Perovskite Synthesis on Curved Solar Cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Excess PbI2 Management via Multimode Supramolecular Complex Engineering Enables High‐Performance Perovskite Solar Cells

Ultrahigh Fill-Factor All-Inorganic CsPbBr3 Perovskite Solar Cells Processed from Two-Step Solution Method and Solvent Additive Strategy

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

Molecule Stapling-Assisted Fabrication of High-Quality CsPbI2Br Films for Efficient and Stable Photovoltaic Modules

Synchronous Elimination of Excess Photoinstable PbI2 and Interfacial Band Mismatch for Efficient and Stable Perovskite Solar Cells

Controllable Grain Morphology Of Perovskite Absorber Film By Molecular Self-Assembly Toward Efficient Solar Cell Exceeding 17%

Improvement of Colloidal Characteristics in a Precursor Solution by a PbI2-(DMSO)2 Complex for Efficient Nonstoichiometrically Prepared CsPbI2.8Br0.2 Perovskite Solar Cells

Efficient Perovskite Solar Cells Fabricated Through CsCl-Enhanced PbI2 Precursor Via Sequential Deposition.