Abstract:PurposeThe purpose of this paper is to present recent work designing a mechanical robotic hand for self‐adaptive grasping, human‐like appearance, which can be used in a humanoid robot. Conventional robotic devices are relatively complex, large, cumbersome and difficult to be installed in a humanoid robot arm. Under‐actuated robot hands use less motors to drive more rotating joints, thus to simplify the mechanical structure, decrease the volume and weight and finally lower the difficulty of control and the cost.Design/methodology/approachA novel under‐actuated finger mechanism is designed, which is based on a gear‐rack mechanism, spring constraint and an active sleeve middle phalanx. The principle analyses of its self‐adaptive grasp and end power grasping are given. A new multi‐fingered hand named as TH‐3R Hand is designed based on the finger.FindingsThe design finger mechanism can be used in a robotic hand to make the hand obtain more degrees of freedom (DOF) with fewer actuators, and good grasping function of shape adaptation, decrease the requirement of control system. TH‐3R Hand has five fingers, 15 DOF. All fingers are similar. TH‐3R Hand has many advantages: it is simple in structure, light in weight, easy to control and low in cost. TH‐3R Hand can passively adapt different shapes and sizes of the grasped object. Experimental studies have demonstrated the self‐adaptation in grasping of the finger.Research limitations/implicationsThe implication of this research is that under‐actuated robotic hands are appropriate for the missions of grasping different objects. The limitation of the research to date is that issues of sensors, control, and communication have not yet been addressed.Practical implicationsKey technologies of the under‐actuated finger and TH‐3R Hand, with self‐adaptive grasping, human‐like appearance and low‐cost lightweight, are feasible. These technologies have the potential to make a significant impact.Originality/valueThese results present a self‐adaptive under‐actuated grasp concept and a humanoid robotic hand with under‐actuated gear‐rack mechanism.

An Adaptive Robot Hand with Spiral Blade Expansion Slide Tube.

A Bioinspired Gripper with Sequential Motion and Mutable Posture Enabled by Antagonistic Mechanism

CSB-II Hand: A Universal Griper with Circular Sliding Bars

On the Design of a Full-Actuated Robot Hand with Target Sensing Self-adaption and Slider Crank Mechanism.

Linearly Parallel and Self-adaptive Robot Hand with Sliding Base Compensation for Grasping on the Surface.

The Development Of A Soft Robot Hand With Pin-Array Structure

Super Under-Actuated Multi-Fingered Mechanical Hand with Modular Self-Adaptive Gear-Rack Mechanism

Design of Humanoid Robotic Hand Based on Link Underactuation

A Flexible Self-Adaptive Underactuated Hand With Series Passive Joints

CTSA Hand: A Novel Cluster-Tube Self-Adaptive Robot Hand

Design of A Novel Robot Finger with Changeable Surface for In-hand Manipulations of Co-fusion Robots

A multi-jointed underactuated robot hand with fluid-driven stretchable tubes

A Linear-parallel and Self-adaptive Underactuated Hand with Parallel Pulleys and Active Linkage.

Development Of A Novel Linear-Parallel Robot Hand

Passive Adaptive Grasp Multi-Fingered Humanoid Robot Hand with High Under-Actuated Function

VGS Hand: A Novel Hybrid Grasping Modes Robot Hand with Variable Geometrical Structure

Dscl Hand: A Novel Underactuated Robot Hand Of Linearly Parallel Pinch And Self-Adaptive Grasp With Double-Slider Co-Circular Linkage Mechanisms

Design of A Cluster Tube Self Adaptive Robot Hand with Function of Fast Grasping.

Design Principle of a Dual-Actuated Robotic Hand With Anthropomorphic Self-Adaptive Grasping and Dexterous Manipulation Abilities

A Three-joint Coupled, Parallel and Self-adaptive Robot Hand

An Underactuated Robot Finger with Movable Skeleton Link and Hoeckens Mechanism for Linear Clamping and Self-adaptive Grasping.