Abstract:Pipelines are widely used in energy power system including thermal power plants and nuclear power plants. In the power system, especially nuclear power plants, as thermal stratification characteristic of nonuniform temperature distribution in the pipe and thermal fatigue such as the low cycle thermal fatigue due to existence of the cycle thermal stress are inevitable, the pipe line system can be destroyed easily and thus affect the normal operation of the power plants. In order to study the pipeline thermal fatigue, the pipeline thermal stress needs to be calculated and therefore the temperature distributions especially the inner wall temperature was needed. The outer wall temperature and working fluid temperature can be obtained with installing measuring tools. The key and difficult point is the estimation of the inner temperature distribution of the pipe. At the same time, in the practical engineering, the pipeline structure with special safety requirements or higher requirements for structural completeness are not allowed to be destroyed by the measuring equipment. Based on the consideration above, this paper presents a method of solving the inverse heat conduction problem, which means the inner temperature distributions can be derived by the outer wall temperature distributions. For the pipe inverse heat conduction problem, this paper applies numerical analysis as the main way. Firstly, the method for transient inverse heat conduction problems applying separation of variables and Duhamel's theorem is established. As the effects of the random error on the measured outer wall temperature are inevitable, the measured data need to be smoothed before used as an input. The Gram orthogonal polynomial method based on the digital filtering theory is applied in this paper to accomplish the smoothing process. The inverse process is accomplished by using MATLAB programming. Then this method is verified in the experiment with high temperature and high pressure. In order to directly validate the accuracy of the inverse analysis, for the test section, not only the transient outer wall temperature and fluid temperature were measured, but also the time dependent middle layer temperature were measured. Then the middle layer temperature obtained from inverse calculation was compared with the measured data from the experiment. The calculated results show that the accuracy of this method is high. The temperature distributions along the radical direction can be obtained quickly and accurate instantaneous heat load for the structural stress analysis and thermal fatiglie analysis can be provided using this method. (CSPE)

Analytical and Numerical Solutions for Transient Heat Conduction in an Infinite Geometry with Heat Source Subjected to Heterogeneous Boundary Conditions of the Third Kind

A numerical method for two-dimensional nonlinear transient inverse heat conduction problems for orthotropic material

Analytical Solution of Heat Conduction for Hollow Cylinders with Time-Dependent Boundary Condition and Time-Dependent Heat Transfer Coefficient

A Computational Method to Solve for the Heat Conduction Temperature Field Based on Data-Driven Approach

An Asymptotic Local Solution for Axi-Symmetric Heat Conduction Problems with Temperature Discontinuity on the Boundary

Transient one-dimensional heat conduction problems solved by finite element

An Extended Method of Fundamental Solutions to the Problems of Inverse Boundary Value of the Heat-conduction Equation Involving One Specific Type of Heat Source

Unconditionally Stable FEM for Transient Linear Heat Conduction Analysis

A general numerical method for solving the three-dimensional hyperbolic heat conduction equation on unstructured grids

Analysis of heat conduction problem involving heat source using Lagrangian equation

Transient Micro-Nano Heat Conduction Analysis Using A Combination of the Finite Difference Method, the Collocation Meshfree Method and the Discrete Ordinate Method

Isogeometric Boundary Element Analysis for 2D Transient Heat Conduction Problem with Radial Integration Method

Application Of Hybrid-Trefftz Element Approach To Transient Heat-Conduction Analysis

BEM for transient nonhomogeneous heat conduction in axisymmetric solids with heat source

Analytical Solution of Hyperbolic Heat Conduction Equation in a Finite Medium Under Pulsatile Heat Source

Analytical Solution for Transient Heat Conduction in Two Semi-infinite Bodies in Contact

New Galerkin-vector Theory and Efficient Numerical Method for Analyzing Steady-State Heat Conduction in Inhomogeneous Bodies Subjected to a Surface Heat Flux

Numerical solutions for the hyperbolic heat conduction problems in a layered solid cylinder with radiation surface

Closed Solutions for Transient Heat Transport in Geological Media: New Development, Comparisons, and Validations

A Numerical Solution For The Transient Inverse Heat Conduction Problem

A general analytical PBEM for solving three-dimensional transient inhomogeneous heat conduction problems with spatially varying heat generation