Abstract:Extreme volume changes and concomitant mechanical instabilities (viz., origin and proliferation of cracking) in Si-based anodes are responsible for premature failure in lithium-ion batteries. Thus, it is a crucial hurdle toward the development of high-performance Si-based batteries, especially in the current scenario of electric vehicles. Accordingly, this research demonstrates a significant improvement in the mechanical stainability of Si-based anode material via in situ incorporation of carbide with a specific design, thereby bestowing outstanding stability in the electrochemical performance. At this juncture, we have established a bridge between nanomechanical and electrochemical properties, investigated via nanoindentation and in-operando stress measurements during electrochemical cycling for Si and in situ reinforced Si–SiC composite. Enhancing the hardness (H) of Si–SiC composite to almost twice as well as enhancing the hardness to effective Young's modulus (E*) ratio (H3/E*2) of the same to almost thrice than that of Si, helped resist the occurrence of plastic deformation and cracking in significant terms. In-operando study shows the typical stress flattening (cum, anisotropic behavior) in the case of the unreinforced Si electrode, which is a manifestation of plastic flow/cracking. By contrast, monotonous stress profiles and absence of the signature of plastic flow/cracking are observed for the Si–SiC electrode, which is an advantage for long cycle life, as observed here. Overall, this kind of experimental study could establish the nanomechanical to electrochemical tie-up, leading to 82% capacity retention over 650 cycles in a Li-ion full-cell along with the Si–SiC composite anode. The "power cycle" of the Si–SiC composite anode, with a variation of current density from 0.5 to 6.0 A g–1, also reveals excellent stability up to 2500 cycles.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.0c02523.Figure S1, an indication of surface roughness variation of unreinforced Si and reinforced Si or Si–SiC pellets, as determined using a profilometer; Figure S2, ToF-SIMS mapping of unreinforced Si pellet; Figure S3, impedance analysis of Si–SiC composite electrode in Li-ion full-cell (with LiCoO2); Figure S4, representation of a schematic of the typical load–displacement curve obtained with nanoindentation; Figure S5, ratio of hardness and effective elastic modulus (H3/E*2) concerning hardness; Figure S6, cracks surrounding or not surrounding microindents, as observed using FEG-SEM for unreinforced Si and reinforced Si or Si–SiC; Figure S7, multibeam optical stress measurement setup for in-operando stress measurement during electrochemical cycling; Figures S8 and S9, in-operando plots for stress profiles, superimposed on the galvanostatic discharge/charge profiles with various experimental parameters; Table S1, discharge capacity and cycle performance literature data for Si–SiC composite; Tables S2 and S3, data from the nanoindentation load–displacement curves for unreinforced Si and reinforced Si (i.e., Si–SiC composite) as well as hardness (H) and effective elastic modulus (E*) obtained from the nanoindentation for the same; Tables S4 and S5, the various materials parameters used for estimating the magnitudes of the stresses, as monitored in-operando during electrochemical cycling (PDF)This article has not yet been cited by other publications.

In Situ Experimental Measurement of Softening of Material Modulus and Stresses Evolution of Si-composite Electrodes During the Electrochemical Process

(Invited) Understanding the Coupled Electrochemical-Mechanical Behavior of Materials for Improving the Performance and Durability of Lithium-Ion Batteries

In situ method for stress measurements in film-substrate electrodes during electrochemical processes: key role of softening and stiffening

Experimental measurement of electro-chemo-mechanical properties of a composite silicon electrode in lithium ion batteries

In Situ Measurement of Mechanical Property and Stress Evolution in a Composite Silicon Electrode

In Situ Atomic-Scale Imaging of Electrochemical Lithiation in Silicon.

In Situ Experimental Measurement of the Mechanical Properties of Carbon-Based Electrodes During the Electrochemical Process

Lithiation of SiO2 in Li-ion Batteries: in Situ Transmission Electron Microscopy Experiments and Theoretical Studies.

Mechanical Property Evolution of Silicon Composite Electrodes Studied by Environmental Nanoindentation

In-situ measurements of electrochemical stress/strain fields and stress analysis during an electrochemical process

Diffusion-Induced Transient Stresses in Li-Battery Electrodes Imaged by Electrochemical Quartz Crystal Microbalance with Dissipation Monitoring and Environmental Scanning Electron Microscopy

Investigation into the impact of charging rates on the stress development within silicon composite electrodes

In-situ Measurements of Mechanical Property and Stress Evolution of Commercial Graphite Electrode

In Situ SEM Observation of Structured Si/C Anodes Reactions in an Ionic-Liquid-Based Lithium-Ion Battery

In Situ Measurement of Strain and Stress Evolution in Lithium Iron Phosphate Electrodes during Electrochemical Cycling

In situ Measurement of Biaxial Modulus of Si Anode for Li-ion Batteries

Real time characterization of the current collector's role on the electro-chemo-mechanical coupling performance of Si composite electrode

Stress Evolution in Composite Silicon Electrodes during Lithiation/Delithiation

Deformation and Chemomechanical Degradation at Solid Electrolyte–Electrode Interfaces

Experimental Measurement of Stress Evolution in Silicon Carbide Composite Electrode During Electrochemical Cycling

Mechanical and Electrochemical Stability Improvement of SiC-Reinforced Silicon-Based Composite Anode for Li-Ion Batteries