Abstract:Active materials used in lithium ion batteries consist of micro-metric ceramic particles. Mechanical failure can happen within these brittle particles due to large internal stresses provoked by lithium intercalating in the crystalline structure during charge and discharge. Their mechanical behavior is directly related to some key intrinsic parameters, namely the elastic modulus, the fracture toughness and lithium di usivity. This works deals with the development of new characterization techniques to quantify these parameters at the local scale. Obtaining quantitative measurements is notably challenging for this type of specimen due to the highly heterogeneous structure of battery electrodes. For this, spinel LiMn2O4-based commercial cathodes are proposed as material of investigation. First, composition analysis of cathode materials at di erent states of charge was done. In general it was noticed that commercial cells are not as consistent as laboratory cells: impurities are often present (Ni, Co,...) and particles can be porous agglomerates of nanoparticles as well as large single grains. However only spinel structure was detected by X-ray di raction and Rietveld analysis showed a typical lattice expansion for higher lithium concentrations. A method using nanoindentation was developed. It consists of applying a large number of indents in cathode cross-sections and subsequently ltering the measurements depending on whether they t the set of hypotheses of the Oliver and Pharr method. It was observed that for decreasing lithium concentrations, the elastic modulus and the hardness increase from 87 GPa (0% State of Charge) to 104 GPa (100% SoC) and from 7.0 GPa (0% SoC) to 8.0 Gpa (100%SoC), respectively. With the help of contact-resonance atomic force microscopy, the elastic property could also be qualitatively mapped and it seems that the particles are homogeneous. Added to micro-raman spectroscopy, it was observed that neighboring particles can have di erent lithiation levels. The fracture toughness was estimated by measuring the crack opening displacement by atomic force microscopy and applying Irwin’s near eld theory. A toughness of about 0.9 MPa·m was found but should not be taken at face-value. Irwin’s theory requires a purely elastic-brittle fracture with traction-free crack walls. Unfortunately this condition cannot be met due to the size of the particles and the toughness is surely overestimated. Associated with electron backscattered di raction, cleavage planes were also evaluated on a reference {111} wafer. It was found that cracks always propagate in the <121> direction, corresponding to {101} planes just below the surface. At higher depths (> 100 nm), the crack deviates of 30 to 40◦. The last part of this work consists of developing a model to better comprehend electrochemical strain microscopy “time spectroscopy” (ESM-TS). It is the most promising technique to quantify locally ionic di usion coe cients. An AFM cantilever is used

In Situ Experimental Measurement of the Mechanical Properties of Carbon-Based Electrodes During the Electrochemical Process

(Invited) Understanding the Coupled Electrochemical-Mechanical Behavior of Materials for Improving the Performance and Durability of Lithium-Ion Batteries

Experimental measurement of electro-chemo-mechanical properties of a composite silicon electrode in lithium ion batteries

Chemo-Mechanical Coupling Measurement of LiMn2O4 Composite Electrode during Electrochemical Cycling

Recent advance into understanding electro-chemo-mechanical behavior of lithium ion batteries by electron microscopy

In Situ Measurement of Mechanical Property and Stress Evolution in a Composite Silicon Electrode

Diffusion-Induced Transient Stresses in Li-Battery Electrodes Imaged by Electrochemical Quartz Crystal Microbalance with Dissipation Monitoring and Environmental Scanning Electron Microscopy

Experimental and Modeling Analysis of Mechanical Response of Composite Electrodes in Lithium Batteries

In Situ Multilength-Scale Tracking of Dimensional and Viscoelastic Changes in Composite Battery Electrodes

In situ method for stress measurements in film-substrate electrodes during electrochemical processes: key role of softening and stiffening

In Situ Monitoring of Gravimetric and Viscoelastic Changes in 2D Intercalation Electrodes

Mechanical characterization of lithium-ion batteries with different chemistries and formats

An in-situ setup for simultaneous electro-chemo-mechanical characterization of electrode materials for lithium-ion battery

Nanomechanics of Li-ion battery materials

Operando Electrochemical Atomic Force Microscopy of Solid–Electrolyte Interphase Formation on Graphite Anodes: The Evolution of SEI Morphology and Mechanical Properties

In-situ measurements of electrochemical stress/strain fields and stress analysis during an electrochemical process

In Situ Observation of Interface Evolution on a Graphite Anode by Scanning Electrochemical Microscopy

Electrochemical-Mechanical Coupling Experiments on Solid-State Battery Materials and Interfaces

A real time study of the coupled electrochemical and mechanical behaviors of the spinel cathodes in LIBs

Electrochemical Stiffness Changes in Lithium Manganese Oxide Electrodes

Deformation and Chemomechanical Degradation at Solid Electrolyte–Electrode Interfaces