Abstract:The substitution behavior of Cu doped into Fe 3 Si and its effect on the electronic structure and mechanical properties of Fe 3 Si were investigated using first principles plane-wave pseudopotential method based on density functional theory. Alloys with dopant Cu taking position of atoms Fe(I), Fe (II), and Si were labeled as Fe 11 CuSi 4 (I), Fe 11 CuSi 4 (II), and Fe 12 Si 3 Cu, respectively. The calculated formation enthalpy and cohesive energy of the three compounds and Fe 3 Si alloy were all negative, indicating their thermodynamic stability. However, the atomic fraction of dopant Cu substituting on Si atom was approximately zero, implying that the formation of Fe 12 Si 3 Cu is challenging. According to the analysis results of differential charge density and Bader charge, the covalent bond was weakened after Cu doping, while the ionic bond strength was in the order of Fe 11 CuSi 4 (I) > Fe 3 Si > Fe 11 CuSi 4 (II) > Fe 12 Si 3 Cu, which also indicated that the Fe 12 Si 3 Cu is less stable than the other three compounds. These results suggested that the dopant Cu atom preferred to substitute Fe atom, particularly Fe(I), but hardly substitute the Si atom. In order to gain a better understanding of the effect of Cu doping on the mechanical properties of Fe 3 Si compound, the antiphase boundary energy (ABPE) and elastic constants of Fe 3 Si, Fe 11 CuSi 4 (I), and Fe 11 CuSi 4 (II) were further calculated. The value of APBE was decreased, whereas the plasticity of Fe 3 Si compound is increased with the substitution of Fe atoms by the Cu dopant. The enhanced plasticity of Fe 3 Si alloy by Cu doping results from the dominant influence of the reduced APBE and weakened covalent bonds over the effect of reduction in ionic bonding.

The Effects of Fe and Si Elements on Structural, Mechanical, and Electronic Properties of an Fe–Si–Ti System by First‐Principles Calculations

Effect of Si on Fe-rich intermetallic formation and mechanical properties of heattreated Al-Cu-Mn-Fe alloys

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Investigation on the lattice vibration, mechanical properties, stress-strain behavior and electronic properties of FeTiSi, CoTiSi and NiTiSi intermetallics from a first-principles calculations

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Substitution behavior of Cu doped into Fe 3 Si and its effect on the electronic structure and mechanical properties based on first-principles calculation

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Anisotropic elasticity, electronic structure and thermodynamic properties of Al-Fe-Si intermetallic compounds from first principles calculations

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Effects of Fe and Si on microstructures and mechanical properties of 2519 aluminum alloy

Effects of Alloying Elements on the Stability of TiO2 and Their Diffusion Properties Studied by First Principles Calculations

Improving Microstructure and Mechanical Properties of Ti43Al5Nb0.1B Alloy by Addition of Fe

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

Changes of alloying elements on elasticity and solid solution strengthening of α-Ti alloys: a comprehensive high-throughput first-principles calculations

Electronic structure and magnetism of Ti2FeSi: A first-principles study

Effect of Fe addition on properties of Ti-6Al-xFe manufactured by blended elemental process

First-principles Calculations to Investigate Elastic Properties, Ideal Tensile Strength and Electronic Properties of TiSi, Ti5Si3 and Ti5Si4

Effect of Si Addition on the Weibull Distribution of Tensile Properties of Fe-bearing Al-Cu Alloys

Influence of TM Elements on the Mechanical and Thermodynamic Properties of Hf2Si Intermetallics

Effects of Fe on Microstructures and High-Temperature Compressive Mechanical Properties of Nb-16Si-22Ti-2Cr-2Al-2Hf Based Alloy

Alloying Effect on the Stability of Ti5Si3 from First‐Principles Study