Abstract:A fully inkjet-printed strain sensor based on carbon nanotubes (CNTs) was fabricated in this study for microstrain and microcrack detection. Carbon nanotubes and silver films were used as the sensing layer and conductive layer, respectively. Inkjet-printed CNTs easily undergo agglomeration due to van der Waals forces between CNTs, resulting in uneven films. The uniformity of CNT film affects the electrical and mechanical properties. Multi-pass printing and pattern rotation provided precise quantities of sensing materials, enabling the realization of uniform CNT films and stable resistance. Three strain sensors printed eight-layer CNT film by unidirectional printing, rotated by 180° and 90° were compared. The low density on one side of eight-layer CNT film by unidirectional printing results in more disconnection and poor connectivity with the silver film, thereby, significantly increasing the resistance. For 180° rotation eight-layer strain sensors, lower sensitivity and smaller measured range were found because strain was applied to the uneven CNT film resulting in non-uniform strain distribution. Lower resistance and better strain sensitivity was obtained for eight-layer strain sensor with 90° rotation because of uniform film. Given the uniform surface morphology and saturated sheet resistance of the 20-layer CNT film, the strain performance of the 20-layer CNT strain sensor was also examined. Excluding the permanent destruction of the first strain, 0.76% and 1.05% responses were obtained for the 8- and 20-layer strain sensors under strain between 0% and 3128 με, respectively, which demonstrates the high reproducibility and recoverability of the sensor. The gauge factor (GF) of 20-layer strain sensor was found to be 2.77 under strain from 71 to 3128 με, which is higher than eight-layer strain sensor (GF = 1.93) due to the uniform surface morphology and stable resistance. The strain sensors exhibited a highly linear and reversible behavior under strain of 71 to 3128 με, so that the microstrain level could be clearly distinguished. The technology of the fully inkjet-printed CNT-based microstrain sensor provides high reproducibility, stability, and rapid hardness detection.

Carbon based Polyimide Nanocomposites Thin Film Strain Sensors Fabricated by Ink-jet Printing Method

Resistance‐type strain sensor based on carbon nanofiber/polypyrrole composite membrane with high sensitivity

3D printed high-performance flexible strain sensors based on carbon nanotube and graphene nanoplatelet filled polymer composites

A Fully Inkjet-Printed Strain Sensor Based on Carbon Nanotubes

Effects of Graphene Morphology on Properties of Carbon Nanotube/Polyurethane Film Strain Sensors

Effects of non-covalent interactions on the properties of 3D printed flexible piezoresistive strain sensors of conductive polymer composites

Effect of Carbon Black on the Strain Sensing Property of 3D Printed Conductive Polymer Composites

Superior Piezoresistive Strain Sensing Behaviors of Carbon Nanotubes in One-Dimensional Polymer Fiber Structure

Thermally stable, adhesively strong graphene/polyimide films for inkjet printing ultrasound sensors

Graphene Nanoplatelets/Polydimethylsiloxane Flexible Strain Sensor with Improved Sandwich Structure

Preparation and Force-Sensitive Properties of Carbon Nanotube/Polydimethylsiloxane Composites Films

Highly Dispersed, Adhesive Carbon Nanotube Ink for Strain and Pressure Sensors

Piezoresistive characteristics of MWNT nanocomposites and fabrication as a polymer pressure sensor

Improvement of the Piezoresistive Behavior of Poly (vinylidene fluoride)/Carbon Nanotube Composites by the Addition of Inorganic Semiconductor Nanoparticles

Fabrication of high sensitivity and stable strain sensors based on composite folded structures via embedded 3D printing

Performance of inkjet-printed strain sensor based on graphene/silver nanoparticles hybrid conductive inks on polyvinyl alcohol substrate

Deformable Strain Sensors Based on Patterned Mwcnts/Polydimethylsiloxane Composites

Inkjet-Deposited Single-Wall Carbon Nanotube Micropatterns on Stretchable PDMS-Ag Substrate–Electrode Structures for Piezoresistive Strain Sensing

A stretchable flexible strain sensor with high sensitivity and fast response fabricated by embedded 3D printing of the hybrid polydimethylsiloxane/conductive carbon paste composites

The Effect of Filler Dimensionality on the Electromechanical Performance of Polydimethylsiloxane Based Conductive Nanocomposites for Flexible Strain Sensors

Thin and high conductive multi‐walled carbon nanotubes/polydimethylsiloxane composite film prepared via solvent method as strain sensors