Abstract:Laser-based metal additive manufacturing technology, which is represented by laser powder bed fusion (LPBF) and direct energy deposition (DED), has been widely used in high-end industries such as aerospace. However, with the rapid development of aerospace equipment, it has become increasingly difficult to meet the requirements of integrated design and manufacturing of metal parts by using LPBF or DED alone. LPBF/DED hybrid laser additive manufacturing technology is expected to greatly improve the overall manufacturing capacity of metal components by combining the advantages of the two technologies. It is expected to break through the limitation of overall manufacturing size, to realize the manufacturing of large and complex aerospace parts, and to reduce the number of components required for large and complex structures to meet the overall design and manufacturing requirements. In this paper, AlSi10Mg was selected as the build material for the LPBF/DED hybrid laser additive manufacturing process and the microstructure and mechanical properties of the as-built samples were studied. The analyses of the microstructure show that there are no obvious defects at the interface between the LPBF zone and the DED zone. Although the phase compositions of both the LPBF zone and the DED zone are composed of alpha-Al matrix and eutectic Si, the melt track shape, microstructural morphology, grain size, grain boundary angle distribution and grain texture change significantly around the LPBF/DED interface. The results of mechanical property tests indicated that the LPBF zone has higher microhardness and tensile strength but lower elongation in comparison with the DED zone. The fine microstructure containing a large number of Si-rich nano-precipitates and high amount of solid solution element enhance the microhardness and tensile strength of the LPBF zone, where the lower solid solubility and high percentage of low angle grain boundary increased the elongation of the DED zone. More importantly, the tensile strength of the LPBF/DED interface is not less than the DED zone, and the boundary of DED melt track as well as porosity defect in the DED zone are the weakest region of LPBF/DED hybrid laser additive manufacturing AlSi10Mg specimens. Therefore, the overall tensile strength of the sample is mainly determined by the DED zone. The formation mechanism of the gradient microstructure around the LPBF/DED interface and the effect of microstructure on properties were also analyzed. This paper proves that the LPBF/DED hybrid laser additive manufacturing technology can be used for the overall manufacturing of aluminum alloy components with regular surface structure.

Microstructure and Mechanical Properties of Laser Metal Deposited AlSi10Mg Alloys

Influence of Laser Process on the Porosity-Related Defects, Microstructure and Mechanical Properties for Selective Laser Melted AlSi10Mg Alloy

Effects Of Porosity On Mechanical Properties Of Laser Metal Deposited Alsi10mg Alloy

Microstructure Evolution and Mechanical Properties of Laser Additive Manufacturing of High Strength Al-Cu-Mg Alloy

Study on microstructure and properties of selective laser melting formed AlSi10Mg alloy

Effects of Laser Processing Parameters on Microstructure and Mechanical Properties of Additively Manufactured AlSi10Mg Alloys Reinforced by TiC

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Achieving Superior Strength and Ductility of AlSi10Mg Alloy Fabricated by Selective Laser Melting with Large Laser Power and High Scanning Speed

Microstructure and mechanical properties of AlSi10Mg alloy built by laser powder bed fusion/direct energy deposition hybrid laser additive manufacturing

Superior strength-ductility synergy and fatigue resistance of heterogeneous structured AZ41 Mg alloy by laser surface processing

Microstructure and mechanical properties of Be–Al alloy fabricated by laser solid forming

Processing defect, microstructure evolution and mechanical properties of laser powder bed fusion Al-12Si alloys

Heterogeneous microstructure and mechanical behaviour of Al-8.3Fe-1.3V-1.8Si alloy produced by laser powder bed fusion

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

Influence of micron and nano SiC<sub>p</sub> on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Aging temperature effects on microstructure and mechanical properties for additively manufactured AlSi10Mg

Influence of micron and nano SiCp on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Tensile behavior of AlSi10Mg overhanging structures fabricated by laser powder bed fusion: Effects of support structures and build orientation

Review on the correlation between microstructure and mechanical performance for laser powder bed fusion AlSi10Mg

Microstructure and mechanical property of high power laser powder bed fusion AlSi10Mg alloy before and after T6 heat treatment

Effect of construction angles on microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting