Abstract:Abstract This paper describes the work conducted by the Canadian Nuclear Safety Commission (CNSC) related to the numerical simulations of reinforced concrete (RC) structures under deformable missile impact. The current paper is a continuation of the work conducted in the frame of the OECD/NEA* IRIS (Improving Robustness Assessment Methodologies for Structures Impacted by Missiles) Phase 3 benchmark project. The concrete mock-up with two simple structures attached, one welded and another bolted, was built and tested at the VTT Technical Research Centre in Espoo, Finland. This mock-up was impacted by three subsequent missiles with varying velocities in order to obtain the damage accumulation. To examine vibration transmission through the mock-up, the simple structures modelling equipment were attached to the rear wall of the structure, while the missile impact was at the centre of the front wall. The parameters of the missiles and the RC structure were selected to ensure a flexible behaviour of the RC target in the impact area with only moderate damages, specifically cracking and permanent deformation without perforation. The non-linear dynamic behaviour of the reinforced concrete slabs under missile impact was analyzed using the commercial FE code LS-DYNA. A hybrid FE model using both 3-D solid and 2-D shell FE models was developed for the target discretization. Since the ultimate objective of this work is to model the entire structure over long time periods, a simplified combined shell-solid model with distributed (smeared) reinforcement was selected and validated. This model employs solid FE around an impact area and shell FE for the rest of the mock-up. Detailed modelling of a large RC structure with all equipment attached leads to a very large finite element (FE) model. Therefore, two-level FE modelling using sub-modelling approach was employed: first, analyze the vibrations of a reinforced concrete structure with simplified equipment modelling, and second, analyze in detail the equipment connected to it. This approach assumes uncoupled dynamic behaviour of the structure and the equipment. While the sub-modelling technique is commonly used in static analysis, a special sensitivity analysis was conducted to prove the applicability of sub-modelling for impact analysis. Finally, the effect of structural damping was examined and the best possible damping was selected. The selected damping values and sub-models resulted in relatively good agreement with the test results for both global (RC mock-up) and local (equipment) behaviour.

Finite Element Analyses on the Soft Projectile Impact Testing of a Wall-floor-wall Reinforced Concrete Structure

Comparative assessment of impact analysis methods applied to large commercial aircraft crash on reinforced concrete containment

Analysis of impact force of large commercial aircraft on rigid wall and nuclear power plant containment

Simulation of Hard-Soft Material Interaction under Impact Loading Employing the Material Point Method

An Integral Numerical Analysis of Impact of a Commercial Aircraft on Nuclear Containment

Numerical Simulation of Blast Loads and Dynamic Response of Reinforced Concrete Slab Subjected to Close-in Explosion

Impact Failure Analysis of Reinforced Concrete Structural Components by Using Finite Element Method

The Shock and Impacting Load Simulation of the Nuclear Power Plant Crashed by the Aircraft

Numerical Analysis of Deformation and Failure of Penetration into Concrete Target by Projectile

Investigating the Effect of Supports on Reinforced Concrete Slab Subjected to Oblique Missile Impact

An Improved Concrete Damage Model for ImpactAnalysis of Concrete Structural Components by usingFinite Element Method

A STUDY FOR EVALUATING LOCAL DAMAGE TO REINFORCED CONCRETE PANELS SUBJECTED TO OBLIQUE IMPACT PART 2: SIMULATION ANALYSIS OF THE EXPERIMENTAL RESULTS OF LOCAL DAMAGE CAUSED BY IMPACT OF DEFORMABLE PROJECTILES

Numerical Analyses of a Shield Building Subjected to a Large Commercial Aircraft Impact

Analytical Study of Perforation Damage in Reinforced Concrete Slabs Subjected to Oblique Impact by Projectiles with Different Nose Shapes

Evaluating concrete material models for blast analysis using 3D finite element analysis

Evaluation of Local Damage to Reinforced Concrete Panels Subjected to Oblique Impact by Soft Missile

Finite element analysis of single steel-plate concrete composite containment of nuclear power plant under commercial aircraft impact

Numerical Simulation of Rigid Projectiles Penetration into Concrete Targets with Different Warhead Shapes

Applicability of Sub-Modelling Technique for Dynamic Analysis of Concrete Structures With Attached Equipment Under Missile Impact

Analytical Model Formulation of Steel Plate Reinforced Concrete Walls against Hard Projectile Impact

Numerical simulation of impact tests on reinforced concrete beams